Shoaib Ahmed

Mr. Shoaib Ahmed

Balochistan University of Information Technology, Engineering and Management Sciences, Quetta, Balochistān, Pakistan
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 July 2022 in Electrical Engineering
Verified
Journal Article
Closed access
PDF file
Shoaib AhmedShoaib Ahmed
Shoaib Ahmed
NANaseer Ahmad
Naseer Ahmad
SKSurat Khan
Surat Khan
Abdin AbdinAbdin Abdin
Abdin Abdin
Irfan SamiIrfan Sami
Irfan Sami

19 March 2022 in Energies
Verified
Journal Article
Open access
PDF file
SKSurat Khan
Surat Khan
Abdin AbdinAbdin Abdin
Abdin Abdin
NANaseer Ahmad
Naseer Ahmad
Shoaib AhmedShoaib Ahmed
Shoaib Ahmed
HKHamid Ali Khan
Hamid Ali Khan
AMAhmad Milyani
Ahmad Milyani
In this research paper, various performances of five different rotor pole topologies of the proposed novel modular stator (MS) permanent magnet (PM) flux reversal machine were investigated. The proposed design had concentrated, non-overlapping winding, which offered high average torque capability at a wide speed range. The no-load performances such as coil test analysis, three-phase flux linkage, flux distribution, back-EMF, and cogging torque, and load analysis, such as average torque versus current density, instantaneous torque, and average electromagnetic torque, were compared. The PM modular stator machine had high cogging torque, which created vibration and noise in the machine. Different cogging torque reduction techniques, such as notching, arc, flange and hybrid technique arc flange, arc notch, notch flange, and arc notch flange, were applied to reduce the cogging torque, improve average load torque, and reduce the induced voltage, harmonics, and torque ripples. The maximum cogging torque decreased by 87.66% and 82% when the arc notch flange and notch arc techniques were applied, respectively, and the minimum effect on cogging torque by the flange technique was 20.66%. Furthermore, the arc flange technique reduced the average torque by 66.72%. The maximum induced voltage was reduced by up to 12.83% using the notch arc technique. The hybrid technique of arc notch flange reduced the harmonics content in flux by 40% and enhanced electromagnetic performance. When applying the hybrid arc notch flange technique, torque ripples were reduced to 90.11%.

1 January 2026 in The Journal of Engineering
Verified
Journal Article
Open access
Shoaib AhmedShoaib Ahmed
Shoaib Ahmed
NANaseer Ahmad
Naseer Ahmad
SKSurat Khan
Surat Khan
LALassi Aarniovuori
Lassi Aarniovuori
JNJanne Nerg
Janne Nerg
JBJan Barta
Jan Barta
Multiphase field‐wound flux switching (FWFS) machines combine the advantages of traditional flux‐switching permanent magnet machines with the benefits of multiphase architectures, including enhanced flux controllability, high fault tolerance, increased torque density and reduced torque ripple. The doubly salient structure contributes to mechanical robustness and structural simplicity, while the utilisation of non‐overlapping windings reduces the volume of copper, which also minimises the production costs of FWFS machines. This paper presents a novel five‐phase outer rotor FWFS machine with non‐overlap windings and investigates four different rotor pole topologies. All the designs are analysed with respect to flux linkage, back‐EMF, cogging torque and electromagnetic torque. Among these configurations, the 10 slot/11 pole configuration demonstrated superior performances, exhibiting high flux linkage and average torque and minimum cogging torque. A deterministic optimisation technique was applied on 10 slot/11 pole topology to further enhance its electromagnetic performance, resulting in a 44.8% increase in average torque along with significant improvements in other parameters. The optimised design was then compared against the existing inner rotor design, showing a 96% increase in torque output. Additionally, the rotor pole designs were optimised to suit direct‐drive applications, confirming the proposed five‐phase design's potential for high speed and high reliability use in electric vehicles and renewable energy systems.

1 January 2026 in IET Electric Power Applications
Verified
Journal Article
Open access
PDF file
MTMatias Tiihonen
Matias Tiihonen
Shoaib AhmedShoaib Ahmed
Shoaib Ahmed
HKHannu Kärkkäinen
Hannu Kärkkäinen
MNMarkku Niemelä
Markku Niemelä
Lassi AarniovuoriLassi Aarniovuori
Lassi Aarniovuori
RBRadu Bojoi
Radu Bojoi
The additional high‐frequency losses present in converter‐fed machines can constitute a significant portion of the overall motor system losses. Until now, no universally accepted method has existed to quantify and analyse these losses. This paper presents a universal method for determining the additional losses caused by pulse width modulation (PWM), which is validated using an induction motor. The proposed approach for segregating high‐frequency harmonic losses assumes that these losses are equivalent to the total harmonic power observed at the motor terminals. The method requires no special arrangements or instrumentation; however, its accuracy naturally depends on the quality of the measurement instruments used. Moreover, this approach adds value to the evaluation of results obtained through the commonly used input–output method for efficiency determination. The ability to explicitly determine high‐frequency harmonic losses in converter‐fed machines opens new opportunities for innovation in motor control systems, modulation strategies and methods for minimising losses in such systems.

22 December 2021
Verified
Conference Paper
Closed access
ABAbdin
Abdin
SKSurat Khan
Surat Khan
NANaseer Ahmad
Naseer Ahmad
HKHamid Ali Khan
Hamid Ali Khan
Shoaib AhmedShoaib Ahmed
Shoaib Ahmed
MHMuzamil Hussain
Muzamil Hussain
The use of induction generator (IG) for small electric power generation at stand alone and grid connected scheme is beneficial in term of capital cost, simple construction, availability, low cost of spare parts and reliability. This work provides a real time comparative analysis of IG using different excitation schemes under different load scenarios. Analysis is made on a real time experiment using capacitor bank excitation and grid excitation scheme. The sole purpose of this work is to test the induction machine’s behavior under different nature of loads and different operation scenarios in laboratory. This analysis declares that when an IG is used in grid connected scheme, it produces power at grid frequency and voltage. Power of the generator is solely depending upon the mechanical input to the rotor. While in standalone scheme variable frequency and voltage problems are observed, this causes to produce power at variable frequency that is unacceptable condition for a power system.

1 January 2026 in IEEE Transactions on Industry Applications
Verified
Journal Article
Open access
Shoaib AhmedShoaib Ahmed
Shoaib Ahmed
Lassi AarniovuoriLassi Aarniovuori
Lassi Aarniovuori
JNJanne Nerg
Janne Nerg
OVOndrej Vitek
Ondrej Vitek
JBJan Barta
Jan Barta