River is one part of the hydrologic cycle. Water in rivers is generally collected from precipitation, such as rain, dew, springs, underground runoff, and in certain countries also comes from melt ice/snow. The height and speed of water in a river is always changing. Changes in altitude and speed of water can affect the surrounding environment. In this paper, we will design a system to measure the altitude and speed of the river. In this work we use Arduino Uno, ultrasonic sensors and flow rate sensors. Ultrasonic sensor HC-SR04 is used as a river height meter. Based on the test results, this sensor has an accuracy of 96.6%.
An accurate information can be useful for authorities to make good policies for preventive and mitigation after volcano eruption disaster. Monitoring of environmental parameters of post-eruption volcano provides an important information for authorities. Such monitoring system can be develop using the Wireless Network Sensor technology. Many application has been developed using the Wireless Sensor Network technology, such as floods early warning system, sun radiation mapping, and watershed monitoring. This paper describes the implementation of a remote environment monitoring system of mount Sinabung post-eruption. The system monitor three environmental parameters: soil condition, water quality and air quality (outdoor). Motes equipped with proper sensors, as components of the monitoring system placed in sample locations. The measured value from the sensors periodically sends to data server using 3G/GPRS communication module. The data can be downloaded by the user for further analysis.The measurement and data analysis results generally indicate that the environmental parameters in the range of normal/standard condition. The sample locations are safe for living and suitable for cultivation, but awareness is strictly required due to the uncertainty of Sinabung status.
1 December 2023 in International Journal of Electrical and Computer Engineering (IJECE)
Power quality is one of the problems in power systems, caused by increased nonlinear loads and short circuit faults. Short circuits often occur in power systems and generally cause voltage sags that can damage sensitive loads. Dynamic voltage restorer (DVR) is an efficient and flexible solution for overcoming voltage sag problems. The control system on the DVR plays an important role in improving the quality of voltage injection applied to the network. DVR control systems based on particle swarm optimization (PSO) and artificial neural networks (ANN) were proposed in this study to assess better controllers applied to DVRs. In this study, a simulation of voltage sag due to a 3-phase short-circuit fault was carried out based on a load of 70% of the total load and a fault location point of 75% of the feeder’s length. The simulation was carried out on the SB 02 Sibolga feeder. Modeling and simulation results are carried out with MATLAB-Simulink. The simulation results show that DVR-PSO and DVR-ANN successfully recover voltage sag by supplying voltage at each phase. Based on the results of the analysis shows that DVR-ANN outperforms DVR-PSO in quality and voltage injection into the network.
1 December 2022 in Indonesian Journal of Electrical Engineering and Computer Science
Fossil energy sources are dwindling. It is necessary to develop alternative energy sources for future energy. The solar cell is an alternative energy that can be used in Indonesia. The current challenge is utilizing solar panels for the best possible power production. This research gives the solution to design an increase in solar cell output power by using mirrors, cooling, and a double-axis solar tracking control system. The results show that using a mirror, cooling, and double-axis solar tracking produces optimal output power with a current and power are 2.43 amperes and 40.3 watts, respectively. Meanwhile, several factors can affect this solar panel's efficiency. Specifically, the amount of solar radiation that the solar panel can receive depends on the climate on the day and location of the research and the solar panel's dimensions.
With the current kWh meter technology installed by PLN (National Electricity Power Company), home users are supplied with electricity consumption information only within a single month. It is difficult for users to observe the change in electricity consumption for further monitoring and planning. In this study, we proposed a tool that can calculate the amount of electricity consumed by home appliances users and send the data in real time and online to the server. This way, users can see the usage of electrical energy periodically. Sensors like current transformator and power transformator were used for this, and the3G module was utilized for data communication. Arduino was used as the main controller of the smart power meter. As a result, we obtained accuracy of current readings was in the range from 88.33% to 99.29%, and accuracy of the voltage readings was in the range from 99.02% to 99.96% compared to standard measurement tools. The result indicated the possibility of using the smart power meter for wider users.