Power reserve control (PRC) becomes esential for modern photovoltaic power plants to meet the increased ancillary service requirements such as grid frequency support. Conventional PRC strategies show obvious limitations in terms of additional hardware requirements, implementation difficulty, and dynamic response. Originated from the linear characteristic of PV curves in the current source region and Lambert-W function, a novel PRC strategy is proposed for the dc/dc converter of a two-stage PV system in order to always achieve the reduced-power operation for any given reference while realizing the real-time maximumum PV power (MPP) estimation with simple implementation. The proposed strategy requires no additional hardwares such as the irradiance and temperature sensors, which realizes sensorless control with reduced cost. Furthermore, cumbersome procudures of curve fitting with sophisticated operating points sampling and key paratmers determination in the real-time MPP estimation by using the conventional PRC methods can be eliminated. In this strategy, the operating point with a curtailed power level is allocated at the left-hand side of the MPP, which guarantees the stability of PV systems under varying conditions. The developed strategy exhibits fast dynamic response, high robustness, and good compatibility with existing PV systems. Simulation and experimental results under variouis scenarios are provided to validate the effectiveness of the proposed strategy.
20 August 2021 in IEEE Transactions on Power Electronics
The dc power transmission system has been obviously attracting more research interests in recent years. In order to satisfy the high-reliability requirement of the dc power transmission system, the power converter should be able to keep uninterrupted operation after multiple unexpected faults. However, high fault-tolerant capability usually leads to the bulky redundant circuit, which increases the cost, volume, and complexity of the power converter. Thus, a fault-tolerant dual active bridge (DAB) converter is proposed to maintain the power transferring ability under multiple unexpected open-circuit faults (OCFs) conditions, which can significantly enhance the reliability of the dc power transmission system. By reconfiguring the central-tapped transformer and two symmetrical auxiliary inductors, the half-bridge conduction branch is built to maintain uninterrupted operation when a single or dual OCF has occurred. The proposed fault-tolerant strategy only requires four extra voltage sensors to detect and locate OCFs for the reconfiguration process. Thus, it significantly improves the system reliability with a low additional cost. Besides, the inductor current, transmission power, and the small-signal models of the proposed fault-tolerant converter have been presented. It proves the proposed fault-tolerant topology can smoothly switch between normal and postfault operation due to the constituency of the inductor current. Finally, the 250-W prototype is designed to verify the advantage of the proposed fault-tolerant DAB converter.
1 July 2021 in IEEE Transactions on Power Electronics
With the increase of the component number, the power stress distribution among differential power processing (DPP) converters, control implementation, system cost, and reliability become the most challenging issues for a practical photovoltaic (PV) DPP system. This article introduces an improved power-rating balance (IPRB) control for the PV-to-bus based DPP architecture that ensures each PV submodule operate at its true maximum power point (MPP) while achieving more balanced power stress distribution and higher reliability. Specifically, a submodule-level finite-state-machine-based MPP tracking is implemented to guarantee always maximum power yield, whereas a string-level power-rating balancing (PRB) control is adopted to balance the unit-maximum proceeded power by DPP converters based on the built power flow model with respect to the string current. A comprehensive comparison of advanced control strategies for PV-to-bus DPP architectures, including least power point tracking, voltage equalization (VE) based PRB control, and the proposed IPRB, has been carried out with the mission-profile-based reliability assessment under different partial shading scenarios. Component-failure-rate-based reliability analysis shows that the PV-to-bus DPP architecture with the proposed IPRB control can significantly improve the system reliability. Main simulation and experimental evaluations are carried out to verify the effectiveness of the proposed control.
16 April 2021 in IEEE Transactions on Transportation Electrification
Current stress is essential for the reliability of power switching devices, especially for high-voltage applications, such as three-level NPC-based dual-active-bridge (3LNPC-DAB) converters. With the conventional single phase shift (SPS) control, the current stress of power devices in 3LNPC-DAB converters is high, which not only affects the conversion efficiency for a wide operating range but also endangers the power devices, which is harmful for the healthy operation of 3LNPC-DAB converters. To solve this problem, this article proposes a minimum-current-stress scheme using particle swarm optimization (PSO) strategy with the aim to reduce the current stress and improve the efficiency of 3LNPC-DAB converters. Different from SPS, two phase shift variables are adopted in the proposed algorithm: one is set between the primary and secondary bridges, and the other is set within the same bridge. Thus, not only the control flexibility is expanded, but also main performance indexes, such as the transmission power, the current stress of each switch, and the efficiency for the whole operating range, are improved. Moreover, the PSO strategy requires fewer parameters to adjust, less computational burden, and faster convergence speed, which simplifies the theoretical calculation and the practical implementation. Finally, the main experimental results for various operating conditions are provided to validate the proposed scheme.
17 August 2023 in IEEE Transactions on Sustainable Energy
Recent power curtailment-based photovoltaic (PV) flexible power point tracking (FPPT) algorithms mainly adopted intricate curve fitting or sophisticated curve-scanning mechanisms to ensure the grid supportive functionalities under partial shading conditions (PSCs), showing the limitations of mathematical solidity or system dynamics improvement. Accordingly, a novel fast-speed partial-shading-tolerant FPPT (PST-FPPT) algorithm is proposed in this article. Regarding the proposed scheme, a modified explicit PV model is developed to express the key operation points with the assistance of several representative current-voltage samples from the initialization process, which is beneficial to computational burden reduction and irradiance sensors removal. Additionally, to guarantee the tracking speed to system dynamics, a set point estimation-based direct voltage regulation strategy is proposed in this article, eliminating the redundant searching in approaching the predefined power command. Simulation and experimental evaluations under various PSCs and operational circumstances validated the effectiveness of the proposed control.
29 April 2022 in IEEE Transactions on Electron Devices
Pulse test techniques are widely adopted in characterizing both the static and dynamic performances of semiconductor devices considering various device structures and operating conditions. For gallium nitride (GaN) devices, due to the current collapse phenomenon, fast and accurate measurement of their key electrical parameters, such as dynamic ON-state resistance ${R}_{\text {ds}, \mathrm{\scriptscriptstyle ON}}$ , switching rising time, fall time, switching losses, and short-circuit (SC) robustness, becomes essential. This article presents a comprehensive review of state-of-the-art pulse test setup methods such as the double-pulse test (DPT), multiple-pulse test (MPT), and SC test (SCT) for the first time, which facilitates the GaN device structure design and practical applications in high efficiency and power density power converters.