To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.
A detailed numerical analysis of secondary flows in a transonic turbine is presented in this paper. The turbine stage is optimized by mitigating secondary flow through the method of non-axisymmetric endwall design. An automated optimization platform of NUMECA/Design3D was coupled with Euranus as a flow solver for the numerical investigation. The contoured endwalls of the stator and the rotor hub were designed based on equidistant Bézier curves along the camber line in the blade channel. The initial design samples were ten times the number of the design variables, and were generated through the LHS method for database generation. The optimization of the endwalls was achieved by using a state-of-the-art multi-objective optimization algorithm, NSGA-II, connected with the BPNN to increase the isentropic efficiency and decrease the secondary kinetic energy, while the mass flow and the degree of reaction were constrained to remain on the datum value as in the original geometry. The individual optimization of the hub endwalls of the stator and the rotor produced an increase in the efficiency of 0.27% and 0.25%, respectively, resulting in a cumulative improvement of 0.46% in the efficiency. The increase in the performance was analyzed at part-load conditions, and it was further confirmed through unsteady simulations.
Two-dimensional design and analysis issues on the meridional surface, which is important in the preliminary design procedure of compressors, are highly dependent on the accuracy of empirical models, such as the prediction of total pressure loss model and turning flow angle. Most of the widely used models are derived or improved from experimental data of some specific cascades with low-loading and low-speed airfoil types. These models may work for most conventional compressors but are incapable of accurately estimating the performance for some specific cases like transonic compressors. The errors made by these models may mislead the final design results. Therefore, surrogate models are developed in this work to reduce the errors and replace the conventional empirical models in the through-flow calculation procedure. A group of experimental data considering a two-stage transonic compressor is used to generate the airfoils database for training the surrogate models. Sensitivity analysis is applied to select the most influential features. Two supervised learning approaches including support vector regression (SVR) and Gaussian process regression (GPR) are used to train the models with a Bayesian optimization algorithm to obtain the optimal hyper parameters. The trained models are integrated into the through-flow code based on streamline curvature method (SLC) to predict the overall performance and internal flow field of the transonic compressor on five rotational speed lines for validation. The predictions are compared with the experimental data and the results of conventional empirical models. The comparison shows that SVR and GPR respectively reduce the predicted error of empirical models by 62.2% and 55.2% for the total pressure ratio and 48.4% and 50.1% for adiabatic efficiency on average. This suggests that the surrogate models constitute an alternative way to predict the performance of airfoils in through-flow calculation where empirical models are inefficient.
To explore the flow mechanism and improve the performance of supersonic tandem rotor blades, the supersonic rotor Rotor37 is taken as the prototype and redesigned to an original supersonic tandem rotor. Then, based on the Kriging model, the physical programming method, and improved particle swarm optimization algorithm, a multi-objective optimization methodology is developed and applied to achieve the multi-objective optimization of the supersonic tandem rotor blades. Compared with Rotor37, the mass flow and surge margin of the original tandem rotor obviously increased. However, the efficiency of the original tandem rotor was slightly lower than Rotor37. After multi-objective optimization, compared with the original tandem rotor, the total pressure ratio and efficiency of the optimized tandem rotor significantly increased, and the efficiency increased by 1.6%. Further, the surge margin increased by 2.75%. The range and intensity of the high-loss region in the middle section of the optimized tandem rotor significantly decreased, and the range of the low-loss area in the middle region and tip region significantly increased, but the range and strength of the high-loss area in the tip region changed a little. The reason for the decrease of total pressure loss in the middle region and tip region is that the three-dimensional optimization of the blade significantly reduced the shock loss and boundary layer separation loss of the front blade. At the same time, the mixing loss between low energy fluid and the main flow in blade wake also reduced. Besides, the three-dimensional optimization of the blade had little impact on the leakage flow and the secondary flow generated by the mutual interference of the leakage flow and shock wave.
A low-speed counter-rotating axial flow compressor (CRAC) with single circumferential grooved casing treatment (CT) was investigated numerically. Both steady and time-accurate numerical calculations were performed to study the effects of the single grooved CTs over the rear rotor on the stability enhancement and the unsteadiness of tip leakage flow (TLF) in the CRAC. Parametric studies indicate that the best position of the single groove should be located near about 20% axial tip chord in terms of the stall margin improvement (SMI). The coincidence of the effective CT locations and the high fluctuating region on blade pressure surface in the smooth wall case shows that the unsteadiness of TLF plays an important role in the stall inception process. Frequency analysis for the static pressure signals near the blade tip shows that both the disappearance of the low frequency components and the suppression of unsteady TLF are beneficial to the SMI. Detailed observation of the flow structures illustrates that the action of the grooves on the different parts of TLF is responsible for the difference of SMI in the CTs. It is more effective to improve the flow stability by controlling the critical TLF released from near the mid-chord.