To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.
Two-dimensional design and analysis issues on the meridional surface, which is important in the preliminary design procedure of compressors, are highly dependent on the accuracy of empirical models, such as the prediction of total pressure loss model and turning flow angle. Most of the widely used models are derived or improved from experimental data of some specific cascades with low-loading and low-speed airfoil types. These models may work for most conventional compressors but are incapable of accurately estimating the performance for some specific cases like transonic compressors. The errors made by these models may mislead the final design results. Therefore, surrogate models are developed in this work to reduce the errors and replace the conventional empirical models in the through-flow calculation procedure. A group of experimental data considering a two-stage transonic compressor is used to generate the airfoils database for training the surrogate models. Sensitivity analysis is applied to select the most influential features. Two supervised learning approaches including support vector regression (SVR) and Gaussian process regression (GPR) are used to train the models with a Bayesian optimization algorithm to obtain the optimal hyper parameters. The trained models are integrated into the through-flow code based on streamline curvature method (SLC) to predict the overall performance and internal flow field of the transonic compressor on five rotational speed lines for validation. The predictions are compared with the experimental data and the results of conventional empirical models. The comparison shows that SVR and GPR respectively reduce the predicted error of empirical models by 62.2% and 55.2% for the total pressure ratio and 48.4% and 50.1% for adiabatic efficiency on average. This suggests that the surrogate models constitute an alternative way to predict the performance of airfoils in through-flow calculation where empirical models are inefficient.
Numerical simulations have been performed to study the effect of the circumferential single-grooved casing treatment (CT) at multiple locations on the tip-flow stability and the corresponding control mechanism at three tip-clearance-size (TCS) schemes in a transonic axial flow compressor rotor. The results show that the CT is more efficient when its groove is located from 10% to 40% tip axial chord, and G2 (located at near 20% tip axial chord) is the best CT scheme in terms of stall-margin improvement for the three TCS schemes. For effective CTs, the tip-leakage-flow (TLF) intensity, entropy generation and tip-flow blockage are reduced, which makes the interface between TLF and mainstream move downstream. A quantitative analysis of the relative inlet flow angle indicates that the reduction of flow incidence angle is not necessary to improve the flow stability for this transonic rotor. The control mechanism may be different for different TCS schemes due to the distinction of the stall inception process. For a better application of CT, the blade tip profile should be further modified by using an optimization method to adjust the shock position and strength during the design of a more efficient CT.
Traditional flow field modeling methods are limited by high computational complexity, making them difficult to apply in practical engineering. This study applies the Dynamic Mode Decomposition (DMD) method to perform reduced-order modeling of unsteady flow fields over an airfoil and a compressor cascade. As a data-driven modal decomposition technique, DMD extracts low-dimensional modes from high-dimensional spatiotemporal data, preserving key dynamic characteristics and significantly reducing computational costs. Numerical simulations were conducted to generate time snapshots, forming matrices of pressure and Mach number snapshots. DMD analysis identified a few dominant modes and their eigenvalues, capturing the primary dynamic behavior of the flow field. The results demonstrate that these modes effectively reconstruct the system’s main characteristics, reducing the need for extensive computational resources and time. The DMD method not only improves modeling efficiency, but also accurately reconstructs complex flow structures. This study validates the feasibility and effectiveness of DMD in reduced-order modeling for unsteady flow fields and includes error analysis for further evaluation.
In this paper, an improved streamline curvature (SLC) approach is presented to obtain the internal flow fields and evaluate the performance of transonic axial compressors. The approach includes some semi-empirical correlations established based on previous literatures, such as minimum loss incidence angle model, deviation model and total pressure loss model. Several developments have been made in this paper for the purpose of considering the influences of three-dimensional (3D) flow in high-loaded multistage compressors with high accuracy. A revised deviation model is applied to predict the cascade with large deflection range. The method for predicting the shock loss is also discussed in detail. In order to validate the reliability of the approach, two test cases including a two-stage transonic fan and a three-stage transonic compressor are conducted. The overall performance and distribution of spanwise aerodynamic parameters are illustrated in this paper. Compared with both the experimental and computational fluid dynamic (CFD) data at design and a number of different off-design condition, the SLC results give reasonable characteristic curves. The validation demonstrates that this improved approach can serve as a fast and reliable tool for flow field analysis and performance prediction in preliminary design stage of axial compressors.