Counter-rotating axial compressor (CRAC) is a promising potential technology to improve the thrust-to-weight ratio of aero-engines, but its special aerodynamic layout usually causes more pronounced flow unsteadiness. Understanding the unsteady flow features and mechanism in the CRAC contributes to the aerodynamic optimization design and flow control strategy organization. A data-driven dynamic mode decomposition method is introduced to investigate the tip flow unsteadiness in a CRAC, and the unsteady features of the tip flow at the design point (DP) and near-stall point (NSP) conditions are revealed. The results show that the 1.0 times blade passage frequency (BPF) and its multi-order harmonic frequency are the dominant frequencies for both rotors at the DP condition. At the NSP condition, the 1.0 BPF is no longer the dominant frequency causing the tip flow unsteadiness, and the low frequency fluctuation of the tip leakage flow becomes the dominant frequency to induce the flow unsteadiness. In the front rotor R1, the unsteady dominant frequency is 1.0 BPF, whereas in the rear rotor R2, the frequency (0.801 BPF and 0.803 BPF) of the tip leakage flow is the dominant frequency. By reconstructing the flow field under the NSP condition, the spatiotemporal evolution of the tip flow during the unsteady stable manifests that the interference effect between the rotors is an important source of the tip flow unsteadiness. The increase in flow unsteadiness leads to an increase in the reconstruction error, indicating that more modes are required to obtain a more accurate reconstruction flow field.
Based on the scale-adaptive simulation, the interaction mechanism between the tip leakage flow (TLF) and the inlet boundary layer (IBL) and its effects on the tip flow field and aerodynamic performance of the compressor cascade were investigated. The time-averaged results show that the IBL reduces the blade tip load near the leading edge region, decreases the axial momentum of the TLF, and inhibits the development of the TLF to a certain extent. On the other hand, the IBL promotes the coupling of the tip leakage vortex, secondary vortex, and separation vortex and induces breakdown, resulting in a large area of severe flow separation in the corner region, greatly reducing the diffusion capacity and significantly increasing the flow loss in the tip region. The analysis of the unsteady transient flow fields indicates that the unsteady fluctuation in the tip region is mainly caused by the tip leakage vortex and flow separation near the blade trailing edge. The former is suppressed under the influence of the IBL, while the latter is amplified. The high-intensity oscillation due to the breakdown and decomposition of the tip vortex structures plays a critical role in the fluctuation of the cascade performance. By means of proper orthogonal decomposition, it is found that the IBL enhances the fluctuation of small-scale vortex structures related to flow separation and leakage flow and makes the stability of the tip flow field worse.
To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.
Numerical simulations have been performed to study the effect of the circumferential single-grooved casing treatment (CT) at multiple locations on the tip-flow stability and the corresponding control mechanism at three tip-clearance-size (TCS) schemes in a transonic axial flow compressor rotor. The results show that the CT is more efficient when its groove is located from 10% to 40% tip axial chord, and G2 (located at near 20% tip axial chord) is the best CT scheme in terms of stall-margin improvement for the three TCS schemes. For effective CTs, the tip-leakage-flow (TLF) intensity, entropy generation and tip-flow blockage are reduced, which makes the interface between TLF and mainstream move downstream. A quantitative analysis of the relative inlet flow angle indicates that the reduction of flow incidence angle is not necessary to improve the flow stability for this transonic rotor. The control mechanism may be different for different TCS schemes due to the distinction of the stall inception process. For a better application of CT, the blade tip profile should be further modified by using an optimization method to adjust the shock position and strength during the design of a more efficient CT.
To investigate the design strategy for load split (LS) and chord length ratio (CR) of highly loaded compressor tandem cascades, the parameterization study of the tandem cascades with different LS and CR was carried out. The parameterization results show that the LS is a crucial design parameter that can be used to regulate performance under off-design conditions. Specifically, lower LS enhances performance at positive incidence angles but comes at the cost of degraded performance at negative incidence angles. Moreover, relatively large CR (2–4) can improve performance under off-design conditions and also plays a role in achieving robust design, but it comes at the expense of optimal performance. To further explore the LS and CR effects on the flow field of the tandem cascades, three additional tandem cascades with LS = 0.5 and different CR were conducted. At large negative incidence angles (LS < 0.5), large CR (2.828) helps mitigate the accumulation of low-energy fluid on the pressure surface of the front blade and enhances the strength of the gap jet. Identically, at large positive incidence angles (LS > 0.5), the large CR mitigates the risk of corner stall and induces a transition in the stall mode of the front blade from corner stall to boundary layer separation over the entire span, further improving the tandem cascade performance. Based on the flow field analysis, the overall design strategy for LS and CR was summarized.
To comprehensively control the corner separation and mid-span boundary layer (BL) separation, this study proposed and evaluated two new flow control configurations. One is a slotted configuration composed of blade-end and whole-span slots, and the other is a combined configuration with end-wall BL suction and whole-span slot. Additionally, the adaptability of the combined configuration to the lower blade solidity (c/t) condition was verified. The results indicate that both the slotted configuration and combined configuration can eliminate the mid-span BL separation, but a better reduction in the corner separation can be observed in the combined configuration. The two configurations can remove the concentrated shedding vortex and reduce the passage vortex (PV) for the datum cascade, but the wall vortex (WV) will be generated. By contrast, the combined configuration has weaker WV and PV than the slotted configuration, which contributes to further reducing the corner separation. In the combined configuration with a c/t of 1.66 and 1.36, the total pressure loss is reduced by 38.4% and 42.1%, respectively, on average, while the averaged static pressure rise coefficient is increased by 16.2% and 17.6%, respectively. This is advantageous for enhancing the working stability and pressure diffusion capacity for compressors. Besides this, the combined configuration with lower c/t can achieve a stronger pressure diffusion capacity and smaller loss than the higher c/t datum cascade. Therefore, the combined configuration is advantageous to the improvement of the aero-engine thrust-to-weight ratio through decreasing the compressor single-stage blade number.