We present a Montecarlo simulator developed in Matlab® for the analysis of a Single Photon Avalanche Diode (SPAD)-based Complementary Metal-Oxide Semiconductor (CMOS) flash Light Detection and Ranging (LIDAR) system. The simulation environment has been developed to accurately model the components of a flash LIDAR system, such as illumination source, optics, and the architecture of the designated SPAD-based CMOS image sensor. Together with the modeling of the background noise and target topology, all of the fundamental factors that are involved in a typical LIDAR acquisition system have been included in order to predict the achievable system performance and verified with an existing sensor.
8 January 2018 in IEEE Transactions on Nuclear Science
We present an FPGA implementation of a Timeto- Digital Converter based on a low cost, low area Spartan 6 device. The converter is based on a tapped delay line model. Several implementation details are discussed with particular focus on critical blocks such as the input stage and thermometerto- binary decoding techniques. We implemented a tap filtering technique to improve the differential non-linearity (DNL) of the single delay line while keeping a good LSB value of 25.57 ps with a single-shot precision (SSP) between 0:69 ÷ 1:46 LSB. Measured DNL and INL lie in the range between −0:90 ÷ 1:23 and −0:43 ÷ 2:96 LSB, respectively. We then implemented an interpolating TDC to overcome the limitations of a single delay line in terms of linearity and measurement range. The interpolating TDC uses the sliding scale technique, where the time interval to be measured is asynchronous with respect to the FPGA clock, achieving DNL and INL in the range −0:072 ÷ 0:070 and −0:755 ÷ 0:872 LSB. SSP is in the 1:096 ÷ 2:815 range. Moreover, we present a novel comparison between the DNLs obtained with two different methods: statistical code density test and using a finely-controlled delay source. Finally, we present the results of a Montecarlo simulation used to investigate the effects of non-linear propagation of the signal through the delay line.
We present an implementation of a semi-device-independent protocol of the generation of quantum random numbers in a fully integrated silicon chip. The system is based on a prepare-and-measure scheme, where we integrate a partially trusted source of photons and an untrusted single photon detector. The source is a silicon photomultiplier, which emits photons during the avalanche impact ionization process, while the detector is a single photon avalanche diode. The proposed protocol requires only a few and reasonable assumptions on the generated states. It is sufficient to measure the statistics of generation and detection in order to evaluate the min-entropy of the output sequence, conditioned on all possible classical side information. We demonstrate that this protocol, previously realized with a bulky laboratory setup, is totally applicable to a compact and fully integrated chip with an estimated throughput of 6 kHz of the certified quantum random bit rate.
We present a new method to acquire the 3D information from a SPAD-based direct-Time-of-Flight (d-ToF) imaging system which does not require the construction of a histogram of timestamps and can withstand high flux operation regime. The proposed acquisition scheme emulates the behavior of a SPAD detector with no distortion due to dead time, and extracts the TOF information by a simple average operation on the photon timestamps ensuring ease of integration in a dedicated sensor and scalability to large arrays. The method is validated through a comprehensive mathematical analysis, whose predictions are in agreement with a numerical Monte Carlo model of the problem. Finally, we show the validity of the predictions in a real d-ToF measurement setup under challenging background conditions well beyond the typical pile-up limit of 5% detection rate up to a distance of 3.8 m.
3 April 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
We present a compact, all-solid-state, low-cost quantum random number generator (QRNG) based on a Single-Photon Avalanche Diode (SPAD) and a Field Programmable Gate Array (FPGA). A new algorithm for random bit generation is described, ranking the inter-arrival times of a group of M photons detected by the SPAD device, and processed directly on the FPGA. The proposed approach improves the efficiency of generated random bits per detected photon, spanning from 0.5 bits/photon in case of 0 order rank, up to 0.875 bits/photon for 2nd order rank. By extending the algorithm to higher orders, the proposed system approaches the maximum theoretical value of 1.0 bit/photon. The rate of generation of random numbers is limited by the SPAD minimum deadtime, achieving an experimentally proven bit rate of 7.3 Mbps. The standard randomness statistical tests are passed for a wide range of photon fluxes and for all the implemented rank orders with no additional post-processing on the generated sequence.