This paper explores the possibility of integrating a smart electromagnetic skin into a street light or traffic light pole to enhance the coverage of a 5G base station operating in the millimeter-waves frequency band with the consequent improvement of the wireless network performance. Specifically, the electromagnetic characteristics of a curved smart electromagnetic skin, which can be easily integrated into a cylindrical radome enclosing the pole, have been analyzed and compared with those of a planar solution. Additionally, the coverage provided by a curved smart electromagnetic skin in a real urban scenario has been considered. The obtained results confirm that using a curved smart electromagnetic skin is both feasible and convenient from several points of view: it guarantees better performance than a planar configuration occupying the same volume, it is simpler to mount and it has a lower visual impact.
The design, the numerical analysis and the experimental characterisation of a convex conformal reflectarray (CRA) has been carried out, with the aim of investigating the feasibility of reflectarrays bent on convex curved surfaces. A medium‐size offset CRA in Ka‐band has been designed, and a demonstrator has been manufactured and measured. The results prove the correctness of the design procedure and the feasibility of this type of antenna, pointing out the differences, also in terms of radiation performances, with respect to a planar reflectarray.
15 December 2022 in IEEE Antennas and Wireless Propagation Letters
In this letter, an innovative ReflectArray (RA) antenna able to radiate in the same direction multiple Orbital Angular Momentum (OAM) modes, is presented: depending on the direction of arrival of the impinging field, the RA radiates a broadside beam carrying on an OAM mode with different index. Two circular RAs with diameter $D = 19.8\lambda$ at the the frequency $f_{0} = 30\,$ GHz, able to radiate two or four OAMs, have been designed and simulated, while a prototype of the dual-mode configuration has also been manufactured and experimentally characterised. The obtained results prove that vortex beams are successfully generated in the range of frequencies from 28 to 32 GHz, confirming the effectiveness of the proposed design.
8 September 2020 in IEEE Open Journal of Antennas and Propagation
Evolutionary algorithms can be successfully exploited for carrying on an effective design of beam-scanning passive reflectarrays, even if the problem is highly non-linear and multimodal. In this paper, the Social Network Optimization (SNO) algorithm has been used for assessing an effective design procedure of a beam-scanning passive reflectarray (RA). For exploiting at most the optimization capabilities of SNO, the entire optimization environment has been deeply analyzed in all its parts. The performance of SNO and the beam-scanning capabilities of the optimized RA have been assessed through the comparison with other well established Evolutionary Algorithms.
15 August 2023 in IEEE Transactions on Antennas and Propagation
In this paper, a dielectric-only reflectarray with a wideband behavior is proposed as an alternative to conventional metallo-dielectric configurations. The introduced unit-cell consists of a single dielectric layer perforated with a square hole located at the center, whose size is used to control the phase of the reflection coefficient. For such a dielectric element, an accurate equivalent circuit model for predicting the reflection coefficient is derived by combining two different concepts: the effective medium theory used to characterize the effective permittivity, and the Floquet modal expansion to describe the wave propagation in terms of Floquet modes. The unit-cell geometrical parameters are then optimized to maximize the reflectarray performance, taking also into account the limitations introduced by the additive manufacturing process adopted for the realization of a prototype. Its experimental characterization confirms the effectiveness of the unit-cell, of the design and manufacturing procedures: in fact, the measurements, in very good agreement with the results of the simulations, prove the significantly low side lobe levels, the good aperture efficiency and the excellent 1-dB bandwidth, larger than 24%.
In this work, the design of a convex conformal reflectarray (CRA), suitable to be used for high gain on board antenna in mobile communication systems, is presented. The reflector is not planar, as in usual reflectarray configurations, but the re-radiating elements are printed on a surface conformed to a cylinder to mimic a curved surface, such as the fuselage of an airplane, on which the reflectarray could be mounted. To compensate for the loss in efficiency due to the curvature, an ad hoc feed is designed; the results obtained with the simulation of the entire structure and the measurements of its prototype prove the effectiveness of the design procedure and its capability in enhancing the CRA features, in comparison with similar but more conventional solutions.