New gas sensing materials, like conductive polymers and nanomaterials-based composites, together with integrated circuit advancements have enabled a new paradigm in gas sensing where a matrix of different types of sensors is used to improve selectivity and sensitivity. In this paper we present a highly flexible read-out circuit for acquiring the dc resistance of the sensors in the matrix. It can measure values from 1 $\text{k}\Omega $ up to 33 $\text{M}\Omega $ , with a minimum SNR of 57 dB. It also offers a wide range of input configuration in terms of resistance and bias voltages to select the optimal bias point for each sensor and to accommodate a large range of sensor types. It achieves very low power consumption at a maximum current consumption of $194~\mu \text{A}$ and an energy per conversion ranging from 1.21 nJ up to 188 nJ thanks to the optimization of the frequency of operation. The circuit was fabricated in a 180 nm bulk CMOS process and a complete characterization of the circuit is presented including current consumption, signal-to-noise ratio, and transfer function. Finally, the circuit was tested in a real application for the measurement of NH 3 and NO 2 using two different types of sensors validating the design objectives and the capability of the read-out circuit for system-on-chip integrations.
Electrical contacts are pervasively found on countless modern devices and systems. It is imperative that connecting components present adequate electrical, mechanical, and chemical characteristics to fulfill the crucial role that they play in the system. To develop an electrical contact material that is tailored for a specific application, different approaches are pursued (e.g., coatings, reinforced composites, alloyed metals, duplex systems, etc.). The manufacturing of electrical contact materials demand a thorough characterization of their electrical properties, mechanical properties, and their resistance to wear, as well as their resistance to atmospheric conditions. Accordingly, commissioning of a novel setup enables a more comprehensive study of the materials that are developed. Therefore, a complete understanding of the material's electrical and tribological characteristics are attained, allowing the production of a material that is compliant with the particular demands of the application for which it is intended. This multipurpose setup was built with higher precision stages and higher accuracy 3-axis force sensor, thus providing the following improvement over the preceding setup: • Elevated load-bearing capacity (double), higher precision and stability. • Tribo-electrical characterization (implementation of scratch and fretting tests). • Environmental control (climate and external vibration).
This paper presents two adaptive biasing techniques for comparators to achieve ultra-low-power and high dynamic range in readout circuits for resistive gas sensors. The first technique is based on an on-demand biasing that generates a bias current up to 3 μA when the differential input voltage is close to zero, while minimizing the bias current when a comparison is not imminent. The second technique takes advantage of the correlation between sensor current and delay requirements to bias the comparator with the appropriate current for each situation. These techniques were applied to two readout circuits, demonstrating a reduction of the energy per measurement to less than a fifth for the largest input resistance in comparison to fixed biasing without affecting SNR. The input range is above 5 decades in both cases, from 2.4 kΩ up to 1GΩ and from 1 kΩ up to 270 MΩ. The signal to noise ratio ranges from 55 dB up to 70 dB which provides enough margin to interface a wide range of gas sensors. Lastly, one of the designs was successfully employed to measure varying concentrations of ammonia with a polypyrrole gas sensor.
Current sensing solutions must combine an ultra-low energy consumption trend with high reliability. The challenge lies on a fine setting of the detection threshold with the assurance of a sufficient sensitivity. In this article, the uncertainty introduced on gas sensing applications by the inherent sensor noise is studied. A 1/f model of the electronic noise in polypyrrole-based ammonia (NH3) sensors is presented and used to estimate the intrinsic signal-to-noise ratio (SNR), giving an effective precision of 10.7 bits, i.e., down to 31.4 ppb in terms of NH3 concentration. No significant improvement in SNR is achieved by increasing the bias voltage and hence the power consumption.
Bioinspired neuromorphic spiking sensors hold great promise for energy-efficient and architecturally simplified neuromorphic networks. Here, an energy-efficient artificial spiking sensor based on a patterned polycrystalline vanadium dioxide (${\text{VO}}_{2}$) memristor grown by direct-current (dc) reactive magnetron sputtering was developed to achieve high sensitivity and low-energy consumption simultaneously. The memristor demonstrates high endurance in both static and dynamic electrical measurements with low cycle-to-cycle variations and excellent spiking performance when integrated into a 1R (memristor)-1T (transistor) spiking circuit. By optimizing the memristor current and output capacitor, the circuit achieves tunable output frequencies of 181--784 kHz under a 5-V supply voltage and an estimated intrinsic capacitance of approximately 0.51 nF. In-sensor temperature encoding is also achieved under a memristor current of 0.1478 mA without an additional external capacitor, exhibiting an excellent sensitivity of $2.98--13.62\text{ }\mathrm{kHz}/\ifmmode^\circ\else\textdegree\fi{}\mathrm{C}$, a low total energy consumption of 2.73--5.63 nJ/spike and a signal-to-noise and distortion ratio (SNDR) of 30.95--41.21 dB from 30 to $50\text{ }\ifmmode^\circ\else\textdegree\fi{}\mathrm{C}$, as well as a high resolution of $0.18\text{ }\ifmmode^\circ\else\textdegree\fi{}\mathrm{C}$ at $47.5\text{ }\ifmmode^\circ\else\textdegree\fi{}\mathrm{C}$. Compared with conventional CMOS readout integrated circuits, the energy consumption can be further reduced by lowering the supply voltage and minimizing the intrinsic capacitance through full circuit integration, while the SNDR can be enhanced by mitigating the stochasticity of ${\text{VO}}_{2}$ and reducing circuit noise, which will require further optimizations of material characteristics and device geometry.