The main focus of this work is to investigate the degradation behavior of two newly developed encapsulants for photovoltaic applications (thermoplastic polyolefin (TPO) and polyolefin elastomer (POE)), compared to the most widely used Ethylene Vinyl Acetate (EVA) upon exposure to two different artificial ageing tests (with and without ultraviolet (UV) irradiation). Additive composition, optical and thermal properties and chemical structure (investigated by means of Thermal Desorption Gas Chromatography coupled to Mass Spectrometry, UV-Visible-Near Infrared spectroscopy, Differential Scanning Calorimetry, Thermogravimetric Analysis and Fourier Transform-Infrared spectroscopy, respectively) of the analyzed polymers were monitored throughout the exposure to artificial ageing tests. Relevant signs of photo-oxidation were detectable for TPO after the UV test, as well as a depletion of material’s stabilizers. Signs of degradation for EVA and POE were detected when the UV dose applied was equal to 200 kW h m⁻². A novel approach is presented to derive information of oxidation induction time/dose from thermogravimetric measurements that correlate well with results obtained by using oxidation indices.

Long-term photovoltaic (PV) module reliability is highly determined by the durability of the polymeric components (backsheet and encapsulation materials). This paper presents the result of experiments on encapsulant degradation influenced by the backsheet permeation properties. Towards this goal, one type of ethylene/vinyl acetate copolymer (EVA) was aged in glass/EVA/backsheet laminates in accelerated aging tests (up to 4000 h for Damp-Heat (DH) and up to 480 kWh/m² for UV and UV-DH combined). The samples contained three backsheets with different permeation properties to examine their impact on EVA degradation. Thermal and chemical characterization shows that the EVA degradation is stronger with the glass–EVA–polyamide (PA)-based backsheet than with the polyethylene terephthalate (PET)-based backsheets. The higher oxygen transmission rate (OTR) of the PA-based backsheet may increase photo-oxidation and aggravating the degradation of EVA in the laminates. Furthermore, FTIR results were used to demonstrate the effect of damp heat exposure on the EVA interfaces, showing an accelerated degradation at the glass–EVA interface. The comparison of accelerated aging stress factors reveals that EVA suffers the strongest chemical and optical degradation when high UV, high temperature and high relative humidity are combined simultaneously.

Most two-dimensional plastic packaging materials are thermally recovered, which does not add to the recycling quota of 50 % required by EU legislation for all lightweight packaging until 2025. Furthermore, the separation processes for 2D materials cannot reach the same level of accuracy, which is possible in the sorting of rigid plastic packaging. This study proposes new adaptations to existing sorting aggregates to increase the near-infrared spectral quality of two-dimensional materials. It aims to improve the spectral quality, which was defined by the deviation of the spectra from a reference spectrum and the variability of the recorded spectra, which can be achieved by installing reflectors behind the material made up of copper or aluminium. This setup enables detection in transflection rather than reflection mode. The variability could be reduced by a factor of 6 through the use of a reflective background. Meanwhile, the spectral fidelity to the reference spectrum could be enhanced, in some cases decreasing the deviation from the reference spectrum by 30 %, which means enhancing a spectrum from unrecognisable to useable. Apart from using reflective materials, the effects of emitter intensity, material and thickness were evaluated.

Polypropylene (PP) recyclates face limitations in their use due to lower qualities compared with virgin PP, resulting from contaminations and the mixing of different PP grades. In particular, their high melt flow rate (MFR) hinders their suitability for applications requiring low MFR, such as pipes. This study investigates the feasibility of producing low MFR PP recyclates from packaging waste. For this purpose, recyclates were produced exclusively from manually sorted extrusion blow molding grades and compared with a recyclate derived from a conventional PP waste stream. Different washing temperatures and recyclate production processes were used to study their effects on the properties of the recyclates. The main objective was to determine the lowest achievable MFR and the rheological, mechanical, and thermal properties of the recyclates from improved sorting. The results are intended to serve as reference points for the evaluation of future automatic sorting trials. The enhanced sorting resulted in an 80% reduction in the MFR and improved ductility, thereby extending the potential applications of the recyclate. The different washing and production processes did not have a significant effect on the investigated properties, except for a slight decrease in the MFR with hot washing and the omission of the pelletizing step.