Sarah-Jane Potts

Dr. Sarah-Jane Potts

Swansea University
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 April 2017 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
CPChris Phillips
Chris Phillips
AAAwadh Al-Ahmadi
Awadh Al-Ahmadi
Sarah-Jane PottsSarah-Jane Potts
Sarah-Jane Potts
TCTim Claypole
Tim Claypole
DDDavide Deganello
Davide Deganello
Conductive inks based on graphite and carbon black are used in a host of applications including energy storage, energy harvesting, electrochemical sensors and printed heaters. This requires accurate control of electrical properties tailored to the application; ink formulation is a fundamental element of this. Data on how formulation relates to properties have tended to apply to only single types of conductor at any time, with data on mixed types of carbon only empirical thus far. Therefore, screen printable carbon inks with differing graphite, carbon black and vinyl polymer content were formulated and printed to establish the effect on rheology, deposition and conductivity. The study found that at a higher total carbon loading ink of 29.4% by mass, optimal conductivity (0.029 Ω cm) was achieved at a graphite to carbon black ratio of 2.6 to 1. For a lower total carbon loading (21.7 mass %), this ratio was reduced to 1.8 to 1. Formulation affected viscosity and hence ink transfer and also surface roughness due to retention of features from the screen printing mesh and the inherent roughness of the carbon components, as well as the ability of features to be reproduced consistently.

10 December 2019 in Journal of Coatings Technology and Research
Verified
Journal Article
Open access
PDF file
Sarah-Jane PottsSarah-Jane Potts
Sarah-Jane Potts
CPChris Phillips
Chris Phillips
EJEifion Jewell
Eifion Jewell
BCBen Clifford
Ben Clifford
YLYin Cheung Lau
Yin Cheung Lau
TCTim Claypole
Tim Claypole
Screen printing is the most widely used process in the production of printed electronics due to its ability to consistently transfer inks containing a wide range of functional materials onto a range of substrates. However, despite its extensive use, the mechanism by which the ink is transferred through the mesh and onto the substrate is not fully understood. Existing theories are contradictory and lack experimental validation. Therefore, high-speed imaging was used in combination with a screen-printing simulation rig that was designed to provide good optical access to study ink deposition during the screen-printing process. The variation in the four stages of ink flow through the screen, described in the theory by Messerschmitt, has been quantified with respect to changes in snap-off distance and squeegee speed. Analyses of the images were compared with measurements of the ink properties and corroborated with analyses of the prints. This has provided a better understanding of the mechanism by which the ink transfers from the mesh to the substrate and subsequently separates in screen printing. This could be used as the basis for the development of predictive algorithms, as well as to improve the understanding of how to optimize print quality and performance.

30 November 2021 in Materials Advances
Verified
Journal Article
Open access
PDF file
CWCARYS WORSLEY
CARYS WORSLEY
DRD. Raptis
D. Raptis
SMSimone Meroni
Simone Meroni
RPR. Patidar
R. Patidar
APA. Pockett
A. Pockett
Trystan M. WatsonTrystan M. Watson
Trystan M. Watson
Green solvent mixes are applied in printed mesoscopic perovskite solar cells and modules, achieving 13.8% PCE at 1 cm 2 and >9% PCE in a 220 cm 2 module. This shows how green solvent engineering can aid improvement and scale-up in emerging technologies.

21 October 2020 in Coatings
Verified
Journal Article
Open access
PDF file
Sarah-Jane PottsSarah-Jane Potts
Sarah-Jane Potts
CPChris Phillips
Chris Phillips
TCTim Claypole
Tim Claypole
EJEifion Jewell
Eifion Jewell
Screen-printable carbon-based inks are available in a range of carbon morphologies and concentrations, resulting in various rheological profiles. There are challenges in obtaining a good print when high loading and elasticity functional inks are used, with a trade-off often required between functionality and printability. There is a limited understanding of how ink rheology influences the ink deposition mechanism during screen-printing, which then affects the print topography and therefore electrical performance. High speed imaging was used with a screen-printing simulation apparatus to investigate the effect of viscosity of a graphite and carbon-black ink at various levels of solvent dilution on the deposition mechanisms occurring during screen-printing. With little dilution, the greater relative volume of carbon in the ink resulted in a greater tendency towards elastic behavior than at higher dilutions. During the screen-printing process this led to the ink splitting into filaments while remaining in contact with both the mesh and substrate simultaneously over a greater horizonal length. The location of separating filaments corresponded with localized film thickness increases in the print, which led to a higher surface roughness (Sz). This method could be used to make appropriate adjustments to ink rheology to overcome print defects related to poor ink separation.

3 January 2022 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
Sarah-Jane PottsSarah-Jane Potts
Sarah-Jane Potts
TKTatyana Korochkina
Tatyana Korochkina
AHAlex Holder
Alex Holder
EJEifion Jewell
Eifion Jewell
CPChris Phillips
Chris Phillips
TCTim Claypole
Tim Claypole
Screen-printing inks containing various morphologies of carbon are used in the production of a variety of printed electronics applications. Particle morphology influences the rheology of the ink which will affect the deposition and therefore the electrical performance of a printed component. To assess the effect of both carbon morphology and concentration on print topography and conductivity, screen printable carbon inks with differing loading concentrations of graphite, carbon black and graphite nanoplatelets (GNPs) were formulated, printed and characterised, with rheological and novel print visualisation techniques used to elucidate the mechanisms responsible. Carbon morphology had significant effects on the packing of particles. The smaller carbon black particles had more interparticle interactions leading to better conductivities, but also higher ink viscosities and elasticities than the other morphologies. Increases in carbon concentration led to increases in film thickness and roughness for all morphologies. However, beyond a critical point further increases in carbon concentration led to agglomerations of particles, mesh marking and increases in surface roughness, preventing further improvements in the print conductivity. The optimal loading concentrations were identifiable using a custom-made screen-printing apparatus used with high speed imaging for all morphologies. Notable increases in filamentation during ink separation were found to occur with further increases in carbon concentration beyond the optimum. As this point could not be identified using shear rheology alone, this method combined with shear rheology could be used to optimise the carbon concentration of screen-printing inks, preventing the use of excess material which has no benefit on print quality and conductivity.

27 February 2019 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
Sarah-Jane PottsSarah-Jane Potts
Sarah-Jane Potts
YLYin Cheung Lau
Yin Cheung Lau
TDThomas Dunlop
Thomas Dunlop
TCTim Claypole
Tim Claypole
CPChris Phillips
Chris Phillips
Binders used in screen-printed carbon-based inks are typically non-conductive. Photonic annealing and subsequent compression rolling have therefore been employed to remove binder and consolidate the conductive particles. Using this method, screen-printable carbon inks containing graphite only, graphite nanoplatelets and a combination of graphite and carbon black were assessed. Photonic annealing leads to the degradation of the polymer binder separating the carbon morphologies, with subsequent compression rolling leading to significant reductions in print film thickness, roughness and improvements in particle orientation. Both processes lead to electrical performance enhancement for all printed inks assessed. The process was most effective for single graphitic morphologies with large gaps between conductors. These saw significant improvements, with reductions in electrical resistivity from 1.91 to 0.23 Ω cm for the graphite ink. The mixed carbon ink saw smaller but still significant improvements in print roughness and resistivity, from 0.037 to 0.019 Ω cm. Therefore, these postprocesses could widen the applications of common, low-cost carbon morphologies in screen printing inks.