Milosan Ioan

Prof. Milosan Ioan

University Transilvania, Braşov, Romania
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 December 2018 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
MPMihai Alin Pop
Mihai Alin Pop
Catalin CroitoruCatalin Croitoru
Catalin Croitoru
TBTibor Bedo
Tibor Bedo
VGVirgil Geamăn
Virgil Geamăn
IRIrinel Radomir
Irinel Radomir
MIMilosan Ioan
Milosan Ioan

11 February 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MIMilosan Ioan
Milosan Ioan
TBTibor Bedo
Tibor Bedo
CGCamelia Gabor
Camelia Gabor
Daniel MunteanuDaniel Munteanu
Daniel Munteanu
MPMihai Alin Pop
Mihai Alin Pop
BVBéla Varga
Béla Varga
The continuous development of modern industries rises the necessity for functionally graded materials. This research starts from the consideration that the incorporation of SiC particles in the molten aluminum alloy can be difficult due to the very low wettability of SiC particles. In order to increase their wettability, SiC particles were covered with a layer of metallic copper. The incorporation of SiC particles into the aluminum alloy mass was performed by centrifugal casting. The secondary hypoeutectic Al-Si alloy used in this study was elaborated within the crucible of a resistors heated furnace. The metallic coating of SiC particles, in addition to the effect of increasing their wettability by molten metal, also has a role in preventing the formation of aluminum carbide in case of heating above 700 °C. A great amount of attention was paid to the parameters used during the centrifugal casting process. The results showed that adjusting the proportion of SiC particles within the composite allows us to obtain values of the thermal expansion coefficient within previously established limits. The present work demonstrates that the coating of SiC particles covered with a thin layer of metallic Cu creates the conditions to easily incorporate them into the molten Al mass, thus obtaining FGMs with controlled properties.

31 July 2025 in Materials
Verified
Journal Article
Open access
PDF file
MIMilosan Ioan
Milosan Ioan
TBTibor Bedo
Tibor Bedo
CGCamelia Gabor
Camelia Gabor
MPMihai Alin Pop
Mihai Alin Pop
Fiber-reinforced composites are gaining more importance across different fields such as aeronautics, automotives, high-performance sporting equipment, etc., where decreasing weight while improving mechanical properties of polymers is fundamental. This article explores the mechanical behavior of fiber-reinforced polyester composite materials, highlighting their advantages and applications in various industrial fields. Usually, composite materials consist of a polyester matrix reinforced with different types of fibers, such as glass, carbon, or Kevlar, which provide superior mechanical characteristics. This study analyzed the tensile strength, bending resistance, and resilience of glass fiber composites, emphasizing the importance of proper fiber selection and manufacturing processes. These materials stand out for their excellent strength-to-weight ratio and are widely used in the fabrication of tanks in various industries. Experimental results demonstrated tensile strength (Rm) around 115 MPa, Shore D hardness values of 88 units, and impact toughness (resilience) of 2.7 J/cm2. Based on the composite materials’ behavior in testing, the article further offers practical recommendations for the effective deployment of these composites in the fabrication of various types of industrial reservoirs.

26 January 2020 in Materials
Verified
Journal Article
Open access
PDF file
MIMilosan Ioan
Milosan Ioan
Monica FlorescuMonica Florescu
Monica Florescu
Dan CristeaDan Cristea
Dan Cristea
Ionelia VoiculescuIonelia Voiculescu
Ionelia Voiculescu
MPMihai Alin Pop
Mihai Alin Pop
TBTibor Bedo
Tibor Bedo
The appropriate selection of implant materials is very important for the long-term success of the implants. A modified composition of AISI 316 stainless steel was treated using solar energy in a vertical axis solar furnace and it was subjected to a hyper-hardening treatment at a 1050 °C austenitizing temperature with a rapid cooling in cold water followed by three variants of tempering (150, 250, and 350 °C). After the heat treatment, the samples were analyzed in terms of hardness, microstructure (performed by scanning electron microscopy), and corrosion resistance. The electrochemical measurements were performed by potentiodynamic and electrochemical impedance spectroscopy in liquids that simulate biological fluids (NaCl 0.9% and Ringer’s solution). Different corrosion behaviors according to the heat treatment type have been observed and a passivation layer has formed on some of the heat-treated samples. The samples, heat-treated by immersion quenching, exhibit a significantly improved pitting corrosion resistance. The subsequent heat treatments, like tempering at 350 °C after quenching, also promote low corrosion rates. The heat treatments performed using solar energy applied on stainless steel can lead to good corrosion behavior and can be recommended as unconventional thermal processing of biocompatible materials.

13 December 2018 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MIMilosan Ioan
Milosan Ioan
Dan CristeaDan Cristea
Dan Cristea
Ionelia VoiculescuIonelia Voiculescu
Ionelia Voiculescu
MPMihai Alin Pop
Mihai Alin Pop
MBMarianne Balat-Pichelin
Marianne Balat-Pichelin
GOGheorghe Oancea
Gheorghe Oancea

19 July 2019 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
JRJose Rodriguez
Jose Rodriguez
Inmaculada CañadasInmaculada Cañadas
Inmaculada Cañadas
MIMilosan Ioan
Milosan Ioan