Junko Umeda

Prof. Dr. Junko Umeda

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2024 in Journal of Magnesium and Alloys
Verified
Journal Article
Open access
XYXu Ye
Xu Ye
ZSZhe Suo
Zhe Suo
ZHZhonghao Heng
Zhonghao Heng
BCBiao Chen
Biao Chen
QWQiuming Wei
Qiuming Wei
JSJianghua Shen
Jianghua Shen

3 April 2021 in Crystals
Verified
Journal Article
Open access
PDF file
JUJunko Umeda
Junko Umeda
LJLei Jia
Lei Jia
Biao ChenBiao Chen
Biao Chen
KCKe Chen
Ke Chen
SLShufeng Li
Shufeng Li
Katsuyohi KondohKatsuyohi Kondoh
Katsuyohi Kondoh
The precipitation and distribution behaviors of in situ-formed titanium boride whiskers (TiB) in TiBw-reinforced Ti-6%Al-4%V (Ti64) composites fabricated from an elemental mixture of Ti64 alloy powder and TiB2 particles by selective laser melting were investigated. The primary precipitation of TiB whiskers strongly depends on B content. For a B content of less than 2 mass%, when the liquid → β-phase transformation occurred and B atoms were discharged, the B-enriched area formed around the β-phase resulted in the generation of TiB whiskers and their agglomeration at the prior β-grain boundaries. When the B content was over 2 mass%, TiB whiskers directly precipitated from the liquid phase and moved to the molten pool boundary via Marangoni convection. As a result, the TiB whiskers were located along the boundary. Furthermore, B-enrichment caused a decrease in the liquidus temperature and thus obstructed β-grain coarsening, and as a result, fine equiaxed α’-grains formed during the phase transformation.

6 August 2016 in Materials
Verified
Journal Article
Open access
PDF file
PPPatchara Pripanapong
Patchara Pripanapong
SKShota Kariya
Shota Kariya
TLTachai Luangvaranunt
Tachai Luangvaranunt
JUJunko Umeda
Junko Umeda
STSeiichiro Tsutsumi
Seiichiro Tsutsumi
Katsuyohi KondohKatsuyohi Kondoh
Katsuyohi Kondoh
Ti and solution treated Mg alloys such as AZ31B (ST), AZ61 (ST), AZ80 (ST) and AZ91 (ST) were successfully bonded at 475 °C by spark plasma sintering, which is a promising new method in welding field. The formation of Ti3Al intermetallic compound was found to be an important factor in controlling the bonding strength and galvanic corrosion resistance of dissimilar materials. The maximum bonding strength and bonding efficiency at 193 MPa and 96% were obtained from Ti/AZ91 (ST), in which a thick and uniform nano-level Ti3Al layer was observed. This sample also shows the highest galvanic corrosion resistance with a measured galvanic width and depth of 281 and 19 µm, respectively. The corrosion resistance of the matrix on Mg alloy side was controlled by its Al content. AZ91 (ST) exhibited the highest corrosion resistance considered from its corrode surface after corrosion test in Kroll’s etchant. The effect of Al content in Mg alloy on bonding strength and corrosion behavior of Ti/Mg alloy (ST) dissimilar materials is discussed in this work.

1 March 2021 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
TTTakuma Teramae
Takuma Teramae
TTTakayuki Tanaka
Takayuki Tanaka
MFMizuki Fukuo
Mizuki Fukuo
KSKazuki Shitara
Kazuki Shitara
JUJunko Umeda
Junko Umeda
Katsuyohi KondohKatsuyohi Kondoh
Katsuyohi Kondoh

1 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
Katsuyohi KondohKatsuyohi Kondoh
Katsuyohi Kondoh
SKShota KARIYA
Shota KARIYA
AKANAK KHANTACHAWANA
ANAK KHANTACHAWANA
Abdulaziz AlHazaaAbdulaziz AlHazaa
Abdulaziz AlHazaa
JUJunko Umeda
Junko Umeda
The decomposition behavior of ZrO2 particles and uniform distribution of Zr and O solutes were investigated by employing in situ scanning electron microscope-electron backscatter diffraction (SEM-EBSD) analysis and thermogravimetric-differential thermal analysis (TG-DTA) to optimize the process conditions in preparing Ti-Zr-O alloys from the pre-mixed pure Ti powder and ZrO2 particles. The extruded Ti-Zr-O alloys via homogenization and water-quenching treatment were found to have a uniform distribution of Zr and O solutes in the matrix and also showed a remarkable improvement in the mechanical properties, for example, the yield stress of Ti-3 wt.% ZrO2 sample (1144.5 MPa) is about 2.5 times more than the amount of yield stress of pure Ti (471.4 MPa). Furthermore, the oxygen solid-solution was dominant in the yield stress increment, and the experimental data agreed well with the calculation results estimated using the Hall-Petch equation and Labusch model.

10 June 2023 in Additive Manufacturing
Verified
Journal Article
Closed access
AIAmmarueda Issariyapat
Ammarueda Issariyapat
JHJeff Huang
Jeff Huang
TTTakuma Teramae
Takuma Teramae
SKShota KARIYA
Shota KARIYA
Abdollah BahadorAbdollah Bahador
Abdollah Bahador
Katsuyohi KondohKatsuyohi Kondoh
Katsuyohi Kondoh