Turbulent free-surface flows are encountered in several engineering applications and are typically characterized by the entrainment of air bubbles due to intense mixing and surface deformation. The resulting complex multiphase structure of the air–water interface presents a challenge in precise and reliable measurements of the free-water-surface topography. Conventional methods by manometers, wave probes, point gauges or electromagnetic/ultrasonic devices are proven and reliable, but also time-consuming, with limited accuracy and are mostly intrusive. Accurate spatial and temporal measurements of complex three-dimensional free-surface flows in natural and man-made hydraulic structures are only viable by high-resolution non-contact methods, namely, LIDAR-based laser scanning, photogrammetric reconstruction from cameras with overlapping field of view, or laser triangulation that combines laser ranging with high-speed imaging data. In the absence of seeding particles and optical calibration targets, sufficient flow aeration is essential for the operation of both laser- and photogrammetry-based methods, with local aeration properties significantly affecting the measurement uncertainty of laser-based methods.

The use of heat pump tumble dryers is nowadays more common because they offer huge energy savings compared to conventional tumble dryers. Earlier studies made on conventional tumble dryers have shown that parameters such as heater power, fan speed, drum speed, weight and initial moisture content of textiles and air leakage have a huge impact on the energy efficiency and drying time. In the present study, a modified commercial heat pump tumble dryer was evaluated for energy consumption and drying time by changing operating parameters including fan speed, drum speed, and mass load. The total energy consumption and drying time were measured and corrected for the initial and final moisture content in the textiles. The experimental results based on 27 drying tests were evaluated to develop linear regression models for energy consumption and drying time, which show a good agreement with the experimental data. The results show that a large mass load, a high drum speed, and a low fan speed give the highest energy efficiency, i.e. the lowest energy consumption per kg of drying load. Larger loads extend the length of the drying cycle while higher fan and drum speeds result in shorter drying time.

This study examines how the inlet air temperature, relative humidity, and flow rate influence the textile drying process in an open cycle tumble dryer. An experimental setup was prepared by connecting a domestic tumble dryer to an external system for controlled heating, humidification, and transport of air. Experiments were conducted by drying cotton textiles (8 kg dry mass) at different air inlet conditions. On the basis of measured data, correlations for determination of the total drying time, the moisture evaporation rate during the constant drying rate, and the area-mass transfer coefficient were developed. The process in the drum was modeled by using an established moisture evaporation model, based on sorption isotherms. A commonly used and a recently reported sorption isotherm for cotton were used with the model. Agreement between calculated and measured drying curves was better in case of the commonly used sorption isotherm, but final moisture content was better predicted by the recently reported sorption isotherm.

Anaerobic digestion in wastewater treatment plants converts its unwanted end product - waste activated sludge into biogas. Even if the process is well established, pre-treatment of the sludge can further improve its efficiency. In this study, four treatment regimes for increasing methane production through prior sludge disintegration were investigated using lab-scale cavitation generator and real sludge samples. Three different cavitating (attached cavitation regime, developed cloud shedding cavitation regime and cavitation in a wake regime) and one non-cavitating regime at elevated static pressure were studied in detail for their effectiveness on physical and chemical properties of sludge samples. Volume-weighted mean diameter D[4,3] of sludge's particles decreased by up to 92%, specific surface area increased by up to 611%, while viscosity (at a shear rate of 3.0 s^-1) increased by up to 39% in the non-cavitating and decreased by up to 24% in all three cavitating regimes. Chemical changes were more pronounced in cavitating regimes, where released soluble chemical oxygen demand (sCOD) and increase of dissolved organic matter (DOM) compounds by up to 175% and 122% were achieved, respectively. Methane production increased in all four cases, with the highest increase of 70% corresponding to 312 mL CH₄ g^-1 COD. However, this treatment was not particularly efficient in terms of energy consumption. The best energy balance was found for the regime with a biochemical methane potencial increase of 43%.

Cavitation erosion is one of the most severe problems encountered in hydraulic turbomachinery. When testing the materials, the engineers usually rely on standardized procedures. The most common one being the vibratory ASTM G-32 test, which offers two possibilities of performing the test - the direct, where the specimen is attached to the ultrasonic device and the indirect, where the specimen is stationary and exposed to the ultrasonic horn, positioned just 0.5 mm from it. The erosion rates from the two are significantly different and a question may be asked if they are at all comparable and further on are they comparable to the "real-life" hydrodynamic cavitation which occurs in turbomachinery. In this study we performed erosion tests on a stationary specimen where the gap between the specimen and the horn was varied from 0.3 to 4 mm. In addition, we used high speed visualization to observe the cavitation in the gap. We observed that the cavitation erosion rate strongly depends on the gap. From visualization we see that the cavitation dynamics significantly changes in a small gap, leading to a large, but 2-dimensional cavitation bubbles which collapse very slowly, compared to the small spherical ones in a larger gap. We investigated the probability of shock wave occurrence and derived a very simple model, which gives accurate qualitative predictions of experimental data. Finally, the study puts into question the validity of ASTM G32 test - the most common approach used in engineering today.

The present study investigates fabric motion in the drum and its effect on performance parameters of a domestic heat pump tumble dryer in several operating points, defined by different load masses and drum speeds. Fabric motion in the drum was recorded by using a high-speed camera and evaluated statistically in order to determine the relation between the fabric distribution and the dryer performance parameters. Multiple regression analysis was performed to develop models for condensate mass flow rate as a function of drum speed, load mass, and drying stage. The results enable optimization of dryer operating parameters with respect to energy efficiency, drying time per kilogram of fabric, and condensate mass flow rate.