Brane Širok

Brane Širok

Auto-generated profile, based on publicly available information

Brane Širok

University of Ljubljana, Faculty of Mechanical Engineering, Ljubljana, Slovenia

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 October 2018 in Drying Technology
Verified
Journal Article
Closed access
PGPero Gatarić
Pero Gatarić
BŠBrane Širok
Brane Širok
MHMarko Hocevar
Marko Hocevar
LNLovrenc Novak
Lovrenc Novak
The use of heat pump tumble dryers is nowadays more common because they offer huge energy savings compared to conventional tumble dryers. Earlier studies made on conventional tumble dryers have shown that parameters such as heater power, fan speed, drum speed, weight and initial moisture content of textiles and air leakage have a huge impact on the energy efficiency and drying time. In the present study, a modified commercial heat pump tumble dryer was evaluated for energy consumption and drying time by changing operating parameters including fan speed, drum speed, and mass load. The total energy consumption and drying time were measured and corrected for the initial and final moisture content in the textiles. The experimental results based on 27 drying tests were evaluated to develop linear regression models for energy consumption and drying time, which show a good agreement with the experimental data. The results show that a large mass load, a high drum speed, and a low fan speed give the highest energy efficiency, i.e. the lowest energy consumption per kg of drying load. Larger loads extend the length of the drying cycle while higher fan and drum speeds result in shorter drying time.

11 September 2018 in Drying Technology
Verified
Journal Article
Closed access
LNLovrenc Novak
Lovrenc Novak
PGPero Gatarić
Pero Gatarić
BŠBrane Širok
Brane Širok
This study examines how the inlet air temperature, relative humidity, and flow rate influence the textile drying process in an open cycle tumble dryer. An experimental setup was prepared by connecting a domestic tumble dryer to an external system for controlled heating, humidification, and transport of air. Experiments were conducted by drying cotton textiles (8 kg dry mass) at different air inlet conditions. On the basis of measured data, correlations for determination of the total drying time, the moisture evaporation rate during the constant drying rate, and the area-mass transfer coefficient were developed. The process in the drum was modeled by using an established moisture evaporation model, based on sorption isotherms. A commonly used and a recently reported sorption isotherm for cotton were used with the model. Agreement between calculated and measured drying curves was better in case of the commonly used sorption isotherm, but final moisture content was better predicted by the recently reported sorption isotherm.

4 March 2020 in Drying Technology
Verified
Journal Article
Closed access
LNLovrenc Novak
Lovrenc Novak
BŠBrane Širok
Brane Širok
MHMarko Hocevar
Marko Hocevar
PGPero Gatarić
Pero Gatarić
The present study investigates fabric motion in the drum and its effect on performance parameters of a domestic heat pump tumble dryer in several operating points, defined by different load masses and drum speeds. Fabric motion in the drum was recorded by using a high-speed camera and evaluated statistically in order to determine the relation between the fabric distribution and the dryer performance parameters. Multiple regression analysis was performed to develop models for condensate mass flow rate as a function of drum speed, load mass, and drying stage. The results enable optimization of dryer operating parameters with respect to energy efficiency, drying time per kilogram of fabric, and condensate mass flow rate.

1 June 2021 in Drying Technology
Verified
Journal Article
Open access
PGPero Gatarić
Pero Gatarić
BŠBrane Širok
Brane Širok
MHMarko Hocevar
Marko Hocevar
LNLovrenc Novak
Lovrenc Novak
This work investigates the evenness of fabric drying in a household heat pump tumble dryer. The evenness of drying was defined as the standard deviation of the fraction of water, evaporated from each fabric item. Drying experiments were performed according to the IEC 61121 standard, which was also followed to determine quantities and types of cotton fabric items (towels, pillowcases and sheets) within each load. Regression analysis was performed to develop models for evenness of drying as a function of load mass and drum speed. Similarities between the tumble dryer energy efficiency parameters and the evenness of drying were analyzed. A high level of agreement was determined between responses of energy efficiency, drying time and evenness of drying to changes in drum speed. Effects of load mass were however more complex and were reflected in a non-linear response of evenness of drying to changes in load mass – the best evenness of drying could be obtained at 2 kg load, followed by 6 kg and 4 kg load. Load composition was determined as an important factor affecting the evenness of drying. At larger loads, a sheet or a pillowcase in average contributed more to the un-evenness of drying than a towel. The presence of sheets and probably the ratio of sheets to other item types in the load were determined as the most probable factors that negatively affected the evenness of drying.

1 December 2013 in Chemical Engineering and Processing - Process Intensification
Verified
Journal Article
Closed access
TPTanja Prešeren
Tanja Prešeren
FSFranci Steinman
Franci Steinman
BŠBrane Širok
Brane Širok
TBTom Bajcar
Tom Bajcar

15 May 2020 in Strojniški vestnik - Journal of Mechanical Engineering
Verified
Journal Article
Open access
BBBenjamin Bizjan
Benjamin Bizjan
BŠBrane Širok
Brane Širok
MBMarko Blagojevič
Marko Blagojevič
In this paper, the process of mineral fiber formation was investigated experimentally on a two-wheel spinner by means of high-speed imaging. Analogue isomalt melt was fiberized at different rotational speeds of spinner wheels, melt flow rates and impingement positions so that the fiberization process was dynamically similar to an industrial mineral wool production process. Images of fiber formation and transport reveal highly complex dynamics of these processes, as fibers mostly occur in form of 3D mutually intertwined structures such as clusters, strands and veils periodically shedding from the melt film. Despite the complexity of flow structures, there is a clear trend of increasing mean fiber length and expansion angle of the coaxial fiber-laden flow as the Weber number and the ratio of melt film velocity to blowing air velocity are increased. The fiberization efficiency (ratio of fiber mass deposited on the collecting mesh to the mass of melt poured) is affected by the impingement position and flow rate of melt as well as the Weber number of melt film. The optimum efficiency was attained at 30° (1 o’clock) impingement position and the ratio of melt film to blowing air flow velocity close to unity.