The environmental concerns of global warming and energy consumption are among the most severe issues and challenges facing human beings worldwide. Due to the relatively higher predicted temperatures (150–180 °C), the latest research on pavement energy consumption and carbon dioxide (CO2) emission assessment mentioned contributing to higher environmental burdens such as air pollution and global warming. However, warm-mix asphalt (WMA) was introduced by pavement researchers and the road construction industry instead of hot-mix asphalt (HMA) to reduce these environmental problems. This study aims to provide a comparative overview of WMA and HMA from environmental and economic perspectives in order to highlight the challenges, motivations, and research gaps in using WMA technology compared to HMA. It was discovered that the lower production temperature of WMA could significantly reduce the emissions of gases and fumes and thus reduce global warming. The lower production temperature also provides a healthy work environment and reduces exposure to fumes. Replacing HMA with WMA can reduce production costs because of the 20–75% lower energy consumption in WMA production. It was also released that the reduction in energy consumption is dependent on the fuel type, energy source, material heat capacity, moisture content, and production temperature. Other benefits of using WMA are enhanced asphalt mixture workability and compaction because the additives in WMA reduce asphalt binder viscosity. It also allows for the incorporation of more waste materials, such as reclaimed asphalt pavement (RAP). However, future studies are recommended on the possibility of using renewable, environmentally friendly, and cost-effective materials such as biomaterials as an alternative to conventional WMA-additives for more sustainable and green asphalt pavements.
Reclaimed asphalt pavement (RAP) has received much attention recently due to its increased use in hot mix asphalt (HMA) pavements to enhance pavement sustainability. The use of aged asphalt in RAP, which is highly oxidised and has lost its properties due to exposure to traffic loads and climatic conditions throughout its lifespan, can cause asphalt mixtures to stiffen and embrittle, thus negatively affecting the behaviour of asphalt mixtures. This issue may be resolved by including rejuvenating agents that can restore both physical and rheological properties of aged asphalt by increasing maltene fractions and decreasing asphaltene. However, the high restoration capacity of any kind of rejuvenating agent does not assure the durability of restored aged asphalt. This study explored the performance and durability of rejuvenated asphalt mixtures embedded with several types of rejuvenators identified from the extensive literature review. The study serves as a significant reference to predict future challenges in rejuvenating aged asphalt.
Machine learning (ML) models are excellent alternative solutions to model complex engineering issues with high reliability and accuracy. This paper presents two extensively explored ensemble models for predicting asphalt pavement temperature, the Markov chain Monte Carlo (MCMC) and random forest (RF). The RF and multiple MCMC (RF-MCMC) were used to hybridise the proposed algorithms for the optimal prediction of asphalt pavement temperature. This study used thermal instruments to measure the asphalt pavement temperature in Gaza Strip, Palestine. The temperature measurements were made at a two-hour interval from March 2012 to February 2013. The temperature data was used to model the pavement temperature. More than 7200 measured pavement temperatures were used to train and validate the proposed models. The validation showed that the ML models are satisfactory. The modelling results ensured the value of the proposed hybridisation models in predicting the asphalt pavement temperature levels. The developed hybrid algorithms regression model achieved acceptable and better prediction results with a coefficient of determination (R2) of 0.96. Generally, the results confirmed the significance of the proposed hybrid model as a reliable alternative computer-aided model for predicting asphalt pavement temperature.
The reclaimed asphalt pavement (RAP) has become a moderately common practice in most countries; Hence, rejuvenating materials with RAP have earned publicity in the asphalt manufacturers, mainly due to the increasing raw material costs. In this study, the crumb rubber (CR) and waste frying oil (WFO) utilized as waste materials to restore the properties and enhance the rutting resistance of the RAP. Several physical, rheological, chemical properties of bituminous binders were tested. The result showed that the RAP bituminous binders incorporating WFO and CR decreased softening points and the increased penetration value; these translate to an increase in penetration index. Moreover, the viscosity of the WFO/CR combination reclaimed asphalt pavement binder showed better workability and stiffness, as well as a low storage stability temperature (less than 2.2 °C) with an acceptable loss upon heating. Without chemical reaction was observed between the waste-frying oil with the rubberized binder and the reclaimed asphalt pavement binder. Additionally, the WFO/CR rheological properties combined with the reclaimed asphalt pavement binder were comparable to the control sample. The incorporation of CR with WFO as a hybrid rejuvenator enhanced the rutting resistance. Therefore, the presence of WFO/CR has a considerable influence on the RAP binder properties while preserving a better environment and reducing pollution by reusing waste materials.
The crumb rubber (CR) recycled from waste tyres could be a viable alternative in achieving green pavements that offer exciting new markets to global investors. Adding CR into flexible pavements enhances their performance and ensures environmental sustainability. This paper will discuss the production variables, CR sizes and contents, blending techniques, optimum bitumen contents, morphology, standard characteristics, rheological characteristics, mechanical performance, greenhouse gas emissions, energy consumption and life cycle cost. This review study found that compared to traditional asphalt mixtures, the CR-modified asphalts had superior performance and longer service life. However, the dearth of information on several factors in CR asphalt production, including greenhouse gas emissions, energy consumption and life cycle cost during recycling, causes many agencies in the global asphalt industry to continue employing costly, energy-consuming additives such as styrene-butadiene-styrene (SBS) instead of CR to enhance asphalt.
The Sultanate of Oman has experienced rapid development over the last thirty years and has constructed environmentally friendly and sustainable infrastructure while it continues to find economical alternative resources to achieve the goals of the Oman 2040 vision. The primary concerns are preserving natural resources and reducing the impact of carbon dioxide (CO₂) emissions on the environment. This review aims to encourage the sustainable use of reclaimed asphalt pavement (RAP) materials in pavement construction and focuses primarily on employing RAP materials in new pavement projects. Currently, new construction projects utilise a significant percentage of demolished asphalt pavement to save costs and natural resources. The key issue that arises when mixing RAP into new asphalt mixtures is the effects on the mixtures’ resistance to permanent disfigurements, such as fatigue cracks, that influence asphalt mixture performance. Numerous studies have assessed the impact of using RAP in asphalt mixtures and found that RAP increases the stiffness of asphalt mixtures, and thus improves rutting resistance at high temperatures. Nevertheless, the findings for thermal and fatigue cracking were found to be contradictory. This review will address the primary concerns regarding the use of RAP in asphalt pavements, and aims to encourage highway agencies and academic researchers in the Gulf countries to develop frameworks for the practical usage of RAP in the construction of sustainable pavement systems.