Reclaimed asphalt pavement (RAP) has received much attention recently due to its increased use in hot mix asphalt (HMA) pavements to enhance pavement sustainability. The use of aged asphalt in RAP, which is highly oxidised and has lost its properties due to exposure to traffic loads and climatic conditions throughout its lifespan, can cause asphalt mixtures to stiffen and embrittle, thus negatively affecting the behaviour of asphalt mixtures. This issue may be resolved by including rejuvenating agents that can restore both physical and rheological properties of aged asphalt by increasing maltene fractions and decreasing asphaltene. However, the high restoration capacity of any kind of rejuvenating agent does not assure the durability of restored aged asphalt. This study explored the performance and durability of rejuvenated asphalt mixtures embedded with several types of rejuvenators identified from the extensive literature review. The study serves as a significant reference to predict future challenges in rejuvenating aged asphalt.

Mineral filler is usually added into asphalt mixture to stiffen the asphalt binder and improve mixture strength. This is particularly important for open gradations such as porous asphalt which is known to have poor strength and durability because of its open nature and large air voids. The interactions that occur between asphalt binder and filler results in certain mastic properties that affect the mixture strength. In this study, the effect of different types of filler on the rheological properties of asphalt–filler mastics for porous asphalt were evaluated using the frequency sweep and multiple stress creep recovery (MSCR) tests. Hydrated lime, cement and diatomite with 2% content were selected to produce asphalt–filler mastic. The influence of diatomite filler was investigated and compared to the hydrated lime and cement fillers. Results indicated that the use of filler increased the stiffness of mastics. The MSCR test showed that hydrated lime and diatomite mastics exhibited the lowest non-recoverable compliance and high recovery than the original PG 76 binder and cement mastic. Diatomite mastic exhibits the best resistance to rutting at high temperatures and stress levels, verifying that the use of diatomite filler is favourable because of its high temperature properties.

This study was initiated to evaluate the performance of asphalt binders and mixtures incorporating linear low-density polyethylene- calcium carbonate (LLDPE-CaCO₃) pellet, either with or without titanate coupling agent. The detailed manufacturing process of modifier pellets was displayed. The coupling agent was used to enhance the cross-linking between materials by means of winding up covalent bonds or molecule chains, thus improving the performance of composites. In the preparation of modified bitumen, the preheated asphalt binder was mixed with the modifiers using a high shear mixer at 5000 rpm rotational speed for 45 min. Experimental works were conducted to evaluate the performance of asphalt binders in terms of volatile loss, viscosity, rutting potential, and low temperature cracking. Meanwhile, the asphalt mixtures were tested using the flow number test and tensile strength ratio (TSR) test. The addition of LLDPE-CaCO₃ modifiers and coupling agent does not significantly affect the volatile loss of modified asphalt binders. The addition of modifiers and coupling agent has significantly improved the resistance to permanent deformation of asphalt binders. Even though, the addition of LLDPE-CaCO₃ modifier and coupling agent remarkably increased the mixture stiffness that contributed to lower rutting potential, the resistance to low temperature cracking of asphalt binder was not adversely affected. The combination of 1% coupling agent with 3% PECC is optimum dosage for asphalt binder to have satisfactory performance in resistance to moisture damage and rutting.

The wide application of reclaimed asphalt pavement (RAP) is hindered due to the highly brittle nature of the material, which contributes a major factor towards cracking-related distresses. While the utilisation of rejuvenating agents has been shown to enhance the flexibility of RAP, they also trigger certain negative effects on the performance of asphalt mixtures. In view of this, potential rejuvenators should be able to alter the rheological properties of asphalts to limit fatigue issues and enhance the potential of low-temperature cracking. Therefore, this study aimed to investigate the possibility of extraction and characterisation of maltene from virgin asphalt (VA) as a potential rejuvenating agent in RAP. Several physicochemical characteristics were examined, including density, viscosity, gas chromatography–mass spectrometry (GC–MS), Fourier-transform infrared (FTIR) spectroscopy, CHNS elemental analysis, and energy dispersive X-ray (EDX) analysis. Finally, the stiffness modulus characteristics of the different types of asphalt binders were evaluated at low and high temperatures. The results demonstrated that maltene was successfully extracted from VA using petroleum ether. In addition, the GC–MS showed that the extracted maltene contained polar and non-polar compounds with low molecular weights compared to VA. Furthermore, the spectra curve of maltene was very similar to that of asphalt, indicating its compatibility with asphalt binder and prospective use. Finally, adding maltene to aged asphalt decreased stiffness values to 0.0063, 0.0499, and 0.0108 MPa, which are equivalent to VA values (0.0061, 0.0481, and 0.0104 MPa) at loading times of 1.0, 0.1, and 0.55 s, respectively. Meanwhile, the stiffness modulus characteristics at low temperature were restored with the addition of maltene.

The creep stiffness and voids properties of asphalt mixture with waste cooking oil at different aging conditions i.e. unaged, short term aging and long term aging were presented in this study. 60/70 penetration grade asphalt binder was used in this investigation. 5% of asphalt binder was replaced with untreated and treated waste cooking oil. The voids properties of asphalt mixture were determined based on Marshall Mix design test where creep stiffness were evaluate through dynamic creep test. In general, the results showed that creep stiffness modulus at the three different aging conditions were improved when treated waste cooking oil was used. However, the creep stiffness was decreased when untreated waste cooking oil was introduced in asphalt mixture.