In this letter, a GaAs-based wideband spoof surface plasmon polariton (SSPP) waveguide with super compact size is presented at millimeter-wave regime. The periodic SSPP unit cell consists of a longitudinal slot and a meander slot in transversal direction, and its corresponding waveguide has good low-pass filtering feature. The momentum of microstrip line for measurement feeding to the SSPPs can be well matched without any gradient transition structures. To apply this SSPP waveguide into the design of bandpass filter (BPF), a row of vias is added with a certain distance from the SSPP unit cells. For demonstration, two on-chip examples, i.e., SSPP waveguide and SSPP-based BPF, are fabricated operating at different frequencies. Good agreement between simulations and measurements validates the propagation characteristics and implementation of the proposed SSPPs.
13 July 2021 in IEEE Microwave and Wireless Components Letters
This letter presents an eighth-order dual-mode waveguide filter, fabricated using the selective laser melting (SLM) technique. The filter employs four dimpled ellipsoid dual-mode resonators, operating at the fundamental TM 101 mode. During printing, the filter can be mechanically self-supported without any internal supports. Compared to the filters employing tuning posts, the proposed filter is less sensitive to fabrication errors in terms of their impacts on passband return loss (RL), frequency shift, and bandwidth. The filter was demonstrated at WR-112 band (7–10 GHz), with a measured insertion loss of 0.25–0.4 dB and an RL >15 dB across the passband of 8–8.46 GHz.
13 October 2022 in IEEE Transactions on Instrumentation and Measurement
In this article, we present a new type of waveguide ground-signal-ground (GSG) probe for millimeter-wave (mmWave) on-wafer measurements. The proposed design integrates a GSG tip, a microcoaxial transmission line (TL), and a waveguide-to-coaxial transition in one structure. The waveguide port of the probe can be inserted into a section of the rectangular waveguide and then directly connected with the vector network analyzer (VNA). To optimize the contact force between the probe tip and the device under test (DUT), the inner and outer conductors of the GSG tip are designed to have different heights. To verify the performance of the proposed design, a W-band (75–110 GHz) prototype is fabricated based on the micrometal additive manufacturing (AM) technology. Due to the unique characteristics of AM technology, the probes can be fabricated in one piece and need no assembly, which significantly reduces the manufacturing cost and eases probe maintenance and repair. The measured results show 0.65–0.90-dB insert loss and over 15-dB return loss (RL) within the whole operating bandwidth, which validates the design mechanism and shows great potential for future economic subterahertz (THz) on-wafer measurements.
2 October 2023 in IEEE Microwave and Wireless Technology Letters
This letter presents a $W$ -band bandpass filter (BPF) with multiple transmission zeros (TZs) based on additively manufactured rectangular micro-coaxial lines (MCLs). Compared to common simple dual behavior resonators (DBRs), the mixed open-short-circuited DBR used in this work creates a pair of TZs nearer to the passband at both sides of the passband. Hence, the maximum 2 $N$ TZs can be obtained for such an $N$ th-order filter without any cross-coupling. A new ordering strategy of DBRs is introduced to realize the design within a significantly limited admittance range of the MCL. As an example, a fourth-order filter with a center frequency of 90 GHz and a fractional bandwidth of 10% is designed, fabricated, and measured. Excellent agreement between simulated and measured results is achieved. The measured passband return loss is better than 15 dB, and the minimum insertion loss (IL) is 1.2 dB. Eight TZs can be obtained, resulting in an excellent roll-off rate and out-of-band rejection.
13 March 2023 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a compact (5mm×56mm) and ultra-wideband directional coupler fabricated by copper additive manufacturing. The coupler is directly synthesized through the even/odd mode extraction algorithm and realized from a pair of coupled air-filled rectangular coaxial lines with working frequency of 0.22-26.5GHz (usable to 10MHz). Periodically loaded polymer strips are embedded with the air-filled coaxial lines to support the inner conductor but this strips also deteriorate the directivity of the coupler. To alleviate this, a special arrangement of the polymer strips is proposed to decrease the unwanted coupling through the strips. As an example, a 27th-order coupler is designed and fabricated, the simulated and measured results have good agreement, showing 20dB of return loss (RL) at all ports, 17dB of coupling, 120 times of frequency ratio and 10-20dB of directivity.
30 April 2020 in IEEE Microwave and Wireless Components Letters
A novel structure parameter estimation method for microstrip bandpass filter (BPF) based on multilayer fully connected network (FCN) is proposed in this letter. We design a network called the main-sub (MS)-Net, which includes the main-network to estimate the structure parameters and the subnetwork to predict the frequency responses of the BPFs. Compared with other neural network-based optimization methods, the MS-Net can generate its own data during the learning process without the need of collecting data sets and pretraining the network. The structure parameters estimated by Main-Net will gradually satisfy the design specifications in the directly iterative learning process. To demonstrate the validity of the proposed method, it was used for designing a third-order and a fifth-order microstrip BPFs. The experiment results show that the proposed method is valid and effective.