Marta Thomas

Mrs. Marta Thomas

Poznań University of Technology, Poznań, Wielkopolskie, Poland
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
RMRadoslaw Mirski
Radoslaw Mirski
MKMarcin Kuliński
Marcin Kuliński
DDDorota Dziurka
Dorota Dziurka
MTMarta Thomas
Marta Thomas
RARyszard Antonowicz
Ryszard Antonowicz
The study analyzed potential applicability for asymmetric reinforcement of glulam beams using materials with a higher modulus of elasticity. Reinforcement elements included smooth and ribbed steel rods as well as basalt rods. These rods were placed only in the tensile zone, assuming that they will not only impart increased rigidity but first of all will reduce the scatter of bending strength values. What is significant, tests were conducted on timber with defects, as it is most commonly used in industrial practice. Analyses showed that this provides an increase in rigidity close to the assumed level. A significant increase in strength was observed. The manufactured beams reinforced with steel and basalt rods were characterized by mean bending strength amounting to 54 and 47 N/mm2, respectively. However, no significant improvement was found in the scatter of the observed variable. Beams reinforced with steel exhibit a 20% higher strength than unreinforced beams. The lower strength of beams reinforced with basalt bars may be related to the lower modulus of elasticity of the basalt itself.

12 September 2022 in Energies
Verified
Journal Article
Open access
PDF file
Barbara KsitBarbara Ksit
Barbara Ksit
Anna Szymczak-GraczykAnna Szymczak-Graczyk
Anna Szymczak-Graczyk
MTMarta Thomas
Marta Thomas
RPRoman Pilch
Roman Pilch
Wood is one of the basic building materials. It is a completely biodegradable raw industrial commodity, the resources of which, with proper forest management, are virtually inexhaustible. Additionally, its acquisition and processing does not require large inputs of fossil fuels. At the same time, forest areas which we obtain wood from neutralize the negative effects of producing and acquiring other raw materials, as one hectare of pine forest (the most popular in Poland) can absorb approx. 20–30 tons of CO2. Wood is characterised by low thermal and electrical conductivity, having simultaneously high sound insulation, which perfectly meets the requirements of the present market and its regulations. This study aimed at verifying the technical parameters of wood, i.e., its bending strength, with the use of an innovative method of the correlation between the bending strength measured along and across wood fibres. The procedure was envisaged as effective for testing the strength of beams in historic buildings, in which—due to their valuable structure—only a limited number of sample holes can be made. The aim of this experiment was to create tables and diagrams, from which, based on the correlation between the side and the head of the beam, using in situ tests and the sclerometric method, it will be possible to derive the bending strength of existing wooden beams. In the study of spruce and pine wood, a correlation between the recess from the side and the recess from the head was found, ranging from 0.64 to 0.76, with an average of 0.72 for spruce elements, and 0.66–0.84, with an average of 0.70 for pine elements. This means that when testing an element fixed in a building, measuring the parameters from the head of the beam with a Schmidt hammer (often such elements are more easily accessible, i.e., on the building facade), the obtained values should be multiplied by 0.72 for spruce elements and by 0.70 for pine elements to obtain the strength of the beam. The authors of this article indicate that the confirmation of this observation requires conducting further research on various types of wood. It should also be noted that the material collected from one batch of sawn timber had a different structure, which was proved by analysing it using SEM imaging. Modeling wood numerically is, to some extent, a simplified issue that assumes wood to be an orthotropic, homogeneous (homogeneous) material. In fact, wood is an anisotropic, very heterogeneous material. The analysis of wood (on the technical scale, construction wood) as an anisotropic material is practically impossible. Adopting wood as an isotropic material is too simplistic. Therefore, the most appropriate methods of strength testing are destructive methods, as all non-destructive methods should not be used without verifying the results with other methods. The results obtained by non-destructive testing pose great difficulties in their interpretation. Obtaining reliable results of experiments entails collecting a large number of research samples. The method described in this paper will allow for obtaining the necessary data for effective expertise assessment regarding the safety level of structural elements in historic wooden load-bearing structures, which is crucial for making conservation decisions.

9 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
MTMarta Thomas
Marta Thomas
Agnieszka ŚlosarczykAgnieszka Ślosarczyk
Agnieszka Ślosarczyk
The article presents durability results for cement mortars made with the addition of slag from municipal waste incineration plants as a replacement for natural aggregate. The undertaken durability tests included frost resistance tests and evaluation of strength, microstructure, water absorption and abrasiveness before and after 150 freeze–thaw cycles. The work reveals that MSWI slag in amounts up to 50 vol. % caused deterioration in the workability and water absorption of cement mortars, regardless of the type of cement used. This, in turn, resulted in a reduction in the compressive and flexural strengths of the composites compared to mortars made with sand alone. Nevertheless, the use of a higher grade of cement, CEM I 52.5 R, resulted in an increase in compressive strength and thus increased the mortars’ frost and abrasion resistance. In addition, after the induced freeze–thaw cycles, mortars made with MSWI slag showed comparable or higher frost and abrasion resistance than those made using natural aggregate.

27 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
MTMarta Thomas
Marta Thomas
MOMałgorzata Osińska
Małgorzata Osińska
Agnieszka ŚlosarczykAgnieszka Ślosarczyk
Agnieszka Ślosarczyk
Limitations in natural aggregate resources and the continuous increase in the demand for concrete as a building material, as well as the increase in the production of waste and the problem with its storage were the reasons for attempts to replace the sand fraction in cement matrices with a corresponding slag fraction. Municipal solid waste incineration (MSWI) slag, which is a product of waste incineration, can be used as an aggregate. This extends its service life and reduces landfill waste. Therefore, three types of cement mortars with different aggregate composition were prepared. In addition, to increase the durability of the cement matrix and the degree of immobilization of harmful heavy metals and salts present in the slag, a natural zeolite with pozzolanic properties was used. A set of tests was carried out on fresh mortar and hardened mortar, including strength tests after 7, 28 and 360 days. What is more, chemical tests were undertaken, including the content of chlorides and sulfates, leaching using the TCLP method and oxide composition. The conducted tests revealed that all mortars had similar strength properties and demonstrated the effectiveness of immobilizing harmful substances contained in the municipal solid waste incineration (MSWI) slag by cementing.

Verified
Journal Article
Open access
PDF file
MTMarta Thomas
Marta Thomas
JKJOANNA KARASIEWICZ
JOANNA KARASIEWICZ
PNPaulina Nowicka-Krawczyk
Paulina Nowicka-Krawczyk
RORafał M. Olszyński
Rafał M. Olszyński
ŁBŁucja Balcerzak
Łucja Balcerzak
Agnieszka ŚlosarczykAgnieszka Ślosarczyk
Agnieszka Ślosarczyk
This study tested the effectiveness of a bifunctional polysiloxane (L43) as a means of protecting concrete surfaces from biocorrosion. L43 was designed to contain two types of functional groups in its structure: surface-active hydrophobic chains and hydrophilic groups that allow the coating to permanently bond to the concrete. L43-coated cement samples achieved compressive strengths exceeding 70 MPa, while samples subjected to cyclic freeze–thaw tests achieved compressive strengths exceeding 33 MPa. In addition, compound L43 at a concentration of 5% reduced the photosynthetic activity of microalgae cells on the concrete surface. The maximum value of chlFI decreased by 69.5%, while the average value decreased by 71.4%. Thus, it was proven that compound L43 effectively counteracts biological corrosion without deteriorating the structure of the impregnated substrate. It should be emphasized that the biocidal effect is due to the structure of the siloxane compound and appropriately selected functional groups. There is no need to add harmful biocides, making the solution environmentally friendly. In addition, the coating allows for free air circulation, which is crucial for the protection of building and construction materials.

17 September 2024 in Materials
Verified
Journal Article
Open access
PDF file
ATAdrian Trociński
Adrian Trociński
DDDorota Dziurka
Dorota Dziurka
MTMarta Thomas
Marta Thomas
RMRadoslaw Mirski
Radoslaw Mirski
Although gypsum-based building materials exhibit many positive characteristics, solutions are still being searched for to reduce the use of gypsum or improve the physico-mechanical properties of board materials. In this study, an attempt was made to produce gypsum boards with hemp fibers. Although hemp fibers can be a specific reinforcement for gypsum-based board materials, they negatively affect the gypsum setting process due to their hygroscopic characteristics. Fibers impregnated with derivatives based on polyvinyl acetate, styrene–acrylic copolymer and pMDI (polymeric diphenylmethane diisocyanate) were used in this study. Gypsum–fiber boards produced with impregnated fibers showed approximately 30% higher mechanical properties as determined by the 3-point bending test. The positive effect of the impregnates on the hemp fibers was confirmed by FTIR (Fourier-transform infrared spectroscopy) and TG/DTA (thermogravimetric analysis/thermal gravimetric analysis) analysis.