This paper presents performance improvement of dual stator axial-flux spoke type permanent magnet vernier machine (DSAFST-PMVM), which has the capability to generate high torque at a lower speed due to magnetic gearing effect. Flux focusing effect is created by means of dual stator single rotor topology with spoke type permanent magnets. It is best suitable for high-performance industrial applications such as servo motors, robot arms, wind power, electric vehicles, and elevator applications. A PM shape is proposed in this paper which has notches in such a way that it produces discrete skew effect which reduces the cogging torque and torque ripples. Optimization of magnet shape is done to make the optimized model more competitive than the proposed and basic models. Main parameters such as back emf, cogging torque, torque ripples, electromagnetic torque, VTHD, airgap flux densities, flux density distribution, power factor, and power of the machine are compared among the basic model, proposed model, and optimized models. The comparative analysis is done by using the time stepped 3D finite element method.
The aim of this paper is to design, analyze and optimize the “Multi-Stack Slotless Axial Flux Switching Permanent Magnet Machine”. In the design process, mathematical models are implemented, and the Finite Element Method (FEM) is performed to analyze the machine performances. The paper aims to minimize the occurrence of cogging torque and torque ripple in the multi-stack slotless stator AFPM machine. As a consequence, it reduces the vibrations in the machine and increases its life span. Multi-stack slotless stator AFPM machine with a right-angled trapezoid-shaped PM is proposed and comparison is done with conventional shape AFPM machine. In order to examine the performance of multi-stack slotless stator AFPM machine Finite Element Analysis (FEA) is used. To further enhance the characteristics of the designed machine with the proposed right-angled PM shape, optimization is done by considering inner and outer pole pitch as the design variables. In optimization process, krigging method assigned with Latin Hyper-cube Sampling and a genetic algorithm (GA) is performed due to suitability with non-linear data. Then, finite element analysis by JMAG-Designer is performed to verify the results. It is determined that optimized model has achieved 65% reduction in torque ripples as compared with the conventional design. Hence, this work attempts to optimize the performance of the AFPM machine.
In this paper, a hexagonal magnet shape is proposed to have an arc profile capable of reducing torque ripples resulting from cogging torque in a single-sided axial flux permanent magnet (AFPM) machine. The arc-shaped permanent magnet increases the air-gap length effectively and makes the flux of the air-gap more sinusoidal, which decreases air-gap flux density and hence causes a reduction in cogging torque. Cogging torque is the basic source of vibration, along with the noise in PM machines, since it is the main cause of torque ripples. Cogging torque is independent of the load current and is proportional to the air-gap flux and the reluctance variation. Three-dimensional finite element analysis (FEA) is used in the JMAG-Designer to analyze the performance of the conventional and proposed hexagonal-shaped PM AFPM machines. The proposed shape is designed to reduce cogging torque, and the voltage remains the same as compared to the conventional hexagonal-shaped PM machine. Further, optimization is performed by utilizing an asymmetric overhang. Latin hypercube sampling (LHS) is used to create samples, the kriging method is applied to approximate the model, and a genetic algorithm is applied to obtain the optimum parameters of the machine.
Axial flux permanent magnet machine (AFPMM) provides high torque characteristics at low speeds without any mechanical gears. AFPMMs have numerous applications in wind energy, electric cars, and direct drive elevator applications. These machines have low cost and improved power to weight ratio. However, single sided AFPM suffers from torque ripples because of its non-sinusoidal back emf, cogging torque, and rotor eccentricity. There are two major components of pulsating torque, namely torque ripples and cogging torque. In PM machine design, the cogging torque is a serious concern because it adds unwanted harmonics to the pulsating torque. Whereas the torque ripples cause noise and vibrations. In order to gain high efficiency, torque ripples should be minimum. The aim of this research is to design “Slotted axial field flux switching permanent magnet machine”. Mathematical models are used to design the machine and Finite element method (FEM) has been used to analyze the machine. In addition, Latin hypercube sampling (LHS) has been used to create the samples. Finally, Kriging Method is used for approximating the model and genetic algorithm has been applied to get the optimum machine. The results showed 61.8 % reduction of the cogging torque in the proposed machine model as compared to the conventional one. Moreover, the optimized model further provided 6.15 % reduction in the cogging torque as compared to the proposed one.
Permanent magnet vernier machines (PMVMs) are becoming progressively attentive because of their high efficiency and high torque density and can thus be utilized for direct-drive applications such as wind power and electric vehicles etc. This paper presents performance improvement of multi-rotor axial flux vernier permanent magnet (MR-AFVPM) machine with a proposed two-stage parallelogram-shaped PM. The proposed shaped PM reduces the cogging torque and torque ripples due to its skew effect. Furthermore, it also presents a comparative analysis of the conventional and proposed shape PM. Then 3D finite element analysis (FEA) is used for comparative analysis. Genetic algorithm (GA) associated with kriging method based on LHS is introduced and is used to optimize the proposed shaped PM for further performance improvement in terms of cogging torque, back EMFs, torque ripples, VTHD, output torque, flux density distributions, power factor and output power of the analyzed machines which are validated by 3D-FEA.
This paper suggests a method to improve the performances of the Dual Stator Axial Flux Spoke-type Permanent Magnet (DSAFSPM) machines with phase group concentrated coil (PGCC) windings, by incorporating continuous and discrete step-skewing along with a special winding connection. The purpose of the study is to mitigate the cogging torque and torque ripples while increasing the output torque so it ameliorates the machine performance at minimum cost for various applications such as wind power plants and electric vehicles (EVs). Cogging torque produces noise and vibrations which degrade the machine’s performance and reduces its life span. The proposed winding sequence enhances the output torque by improving its distribution factor along with the use of continuous skew and step-skew magnets. This research work improved the cogging torque and torque ripples with the help of skew techniques while output torque is increased by the proposed winding sequence. Further harmonics and ripples are also mitigated by the proposed winding sequence. The overall machine volume is kept constant along with the magnet size and the design parameters for fair performance analysis. Comparative analysis of these machines is performed using three-dimensional (3-D) time-stepped finite element analysis (FEA). Proposed model I and proposed model II reduce the harmonics by 42% and 23%, respectively. By using continuous skew and discrete step-skew magnets, cogging torque is reduced up to 81.5% and 75%, respectively. This reduction in cogging torque reduces the noise and vibration in machines which assists the machines to perform a smooth operation. The reduction in output torque ripples in proposed model I is 60.8% while that of proposed model II is 59.3%.