Crack-free AlN films with threading dislocation density (TDD) below 109 cm−2 are needed for deep-UV optoelectronics. This is typically achieved using pulsed lateral overgrowth or very thick buffer layers (>10 μm), a costly and time-consuming approach. A method for conventional metalorganic chemical vapor deposition growth of AlN/SiC films below 3 μm with greatly improved quality is presented. Focusing on substrate pretreatment before growth, we reduce average film stress from 0.9 GPa (tension) to −1.1 GPa (compression) and eliminate cracking. Next, with optimized growth conditions during initial deposition, AlN films with x-ray rocking curve widths of 123 arc-sec ( ) and 304 arc-sec ( ) are developed, and TDD is confirmed via plan view transmission electron microscopy (TEM) to be 2 108 cm−2. Film stress measurements including x-ray 2θ-ω, reciprocal space mapping, and curvature depict compressively stressed growth of AlN on 4H-SiC due to lattice mismatch. The thermal expansion coefficient mismatch between AlN and SiC is measured to be and is found to be constant between room temperature and 1400 °C. TEM confirms the existence of dense misfit dislocation (MD) networks consistent with MD formation near SiC step edges and low MD density regions attributed to nearly coherent AlN growth on SiC terraces. These low-TDD, crack-free AlN/SiC buffers provide a platform for deep-UV optoelectronics and ultrawide bandgap electronics.
High performance InGaN micro-size light-emitting diodes (µLEDs) with epitaxial tunnel junctions (TJs) were successfully demonstrated using selective area growth (SAG) by metalorganic chemical vapor deposition (MOCVD). Patterned n + GaN/n-GaN layers with small holes were grown on top of standard InGaN blue LEDs to form TJs using SAG. TJ µLEDs with squared mesa ranging from 10×10 to 100×100 µm2 were fabricated. The forward voltage (Vf) in the reference TJ µLEDs without SAG is very high and decreases linearly from 4.6 to 3.7 V at 20 A/cm2 with reduction in area from 10000 to 100 µm2, which is caused by the lateral out diffusion of hydrogen through sidewall. By contrast, the Vf at 20 A/cm2 in the TJ µLEDs utilizing SAG is significantly reduced to be 3.24 to 3.31 V. Moreover, the Vf in the SAG TJ µLEDs is independent on sizes, suggesting that the hydrogen is effectively removed through the holes on top of the p-GaN surface by SAG. The output power of SAG TJ µLEDs is ∼10% higher than the common µLEDs with indium tin oxide (ITO) contact.
AlGaN-based UV-A LEDs have wide applications in medical treatment and chemical sensing; however, their efficiencies are still far behind visible LEDs or even shorter wavelengths UV-C counterparts because of the large lattice mismatch between the low-Al-content active region and the AlN substrate. In this report, we investigated the composition and thickness of the quantum barrier in the active region in terms of LED performance. Due to the improved strain management and better carrier confinement, efficient UV-A LEDs (320 nm - 330 nm) with EQEs up to 6.8% were demonstrated, among the highest efficiencies at this wavelength range.
Micro-light-emitting diodes (µLEDs) are gathering significant interest as a technology for emerging micro-displays. However, µLEDs encounter numerous obstacles, including size-dependent efficiency loss, poor efficiency of red µLEDs, and challenges associated with the mass transfer and integration of full-color µLEDs. These issues become more acute in ultra-small µLEDs (<5 µm), which were required by the augmented reality (AR) displays. Here, we discuss the principal challenges faced by µLEDs and explore the possible solutions. We highlight recent advances in InGaN-based RGB µLEDs tailored for AR displays. In particular, we discuss the advancements in ultra-small InGaN µLEDs scaled down to 1 µm, the developments in InGaN red µLEDs, and the implementation of tunnel junction-based cascaded InGaN µLEDs for monolithic integration.
The impact of AlGaN growth conditions on AlGaN:Si resistivity and surface morphology has been investigated using metalorganic chemical vapor deposition. Growth parameters including growth temperature, growth rate, and trimethylindium (TMI) flow have been systematically studied to minimize the resistivity of AlGaN:Si. We observed a strong anticorrelation between AlGaN:Si conductivity and growth temperature, suggesting increased silicon donor compensation at elevated temperatures. Secondary ion mass spectrometry and positron annihilation spectroscopy ruled out compensation by common impurities or group-III monovacancies as a reason for the observed phenomenon, in contrast to theoretical predictions. The underlying reason for AlGaN:Si resistivity dependence on growth temperature is discussed based on the possibility of silicon acting as a DX center in Al0.65Ga0.35N at high growth temperatures. We also show remarkable enhancement of AlGaN:Si conductivity by introducing TMI flow during growth. A minimum resistivity of 7.5 mΩ cm was obtained for n-type Al0.65Ga0.35N, which is among the lowest reported resistivity for this composition.