The press and sinter method remains the standard among powder metallurgy processes for powdered stainless-steel materials. It delivers low cost, low oxidation rate, and adequate corrosion resistance. Furthermore, 17-4PH is a martensitic stainless-steel that is commonly used for high-strength and medium-ductility stainless steel parts. However, a few studies have investigated the press and sinter method for producing 17-4PH parts. This shortage is due to the high hardness (low compressibility) of 17-4PH powder. Thus, the main objective of this study is to evaluate the press and sinter method in terms of the manufacturing process, the influencing factors, and the theoretical basis of press and sinter methods in conjunction with metal injection molding technology for the production of 17-4PH parts. First, the literature and monographs are examined and summarized to cover the previous results, research progress, development trends, and applications of press and sinter method 17-4PH parts. Following the theoretical analysis, the practical investigation was conducted by producing parts with cold pressing from 800 to 1600 MPa, followed by sintering: the sintering temperature was 1200 °C for one hour under a protective vacuum atmosphere. ImageJ analysis was performed to measure the sinter density. The results showed an increase in relative sinter density from 84.43% to 96.43% for 800 and 1600 MPa, respectively, while the earlier results reached 93.47%. Overall, the press and sinter method enables the production of high-hardness 17-4PH parts with a high density, without using additives like lubricants, wax, or alloying elements.
1 June 2015 in Archives of Metallurgy and Materials
The scope of the research work is the production and characterization of Al matrix composites reinforced with WC ceramic nanoparticles. The synthesis process was powder metallurgy. The produced composites were examined as far as their microstructure and mechanical properties (resistance to wear, micro/macrohardness). Intermetallic phases (Al12W and Al2Cu) were identified in the microstrucutre. Al4C3 was not detected in the composites. Adding more than 5 wt% WC to the aluminum, microhardness and wear resistance exceed the values of Al alloy. Composites having weak interface bond performed the highest wear rate
Titanium and its alloys have excellent corrosion resistance, heat, and fatigue tolerance, and their strength-to-weight ratio is one of the highest among metals. This combination of properties makes them ideal for aerospace applications; however, high manufacturing costs hinder their widespread use compared to other metals such as aluminum alloys and steels. Powder metallurgy (PM) is a greener and more cost and energy-efficient method for the production of near-net-shape parts compared to traditional ingot metallurgy, especially for titanium parts. In addition, it allows us to synthesize special microstructures, which result in outstanding mechanical properties without the need for alloying elements. The most commonly used Ti alloy is the Ti6Al4V grade 5. This workhorse alloy ensures outstanding mechanical properties, demonstrating a strength which is at least twice that of commercially pure titanium (CP-Ti) grade 2 and comparable to the strength of hardened stainless steels. In the present research, different mixtures of both milled and unmilled Cp-Ti grade 2 powder were utilized using the PM method, aiming to synthesize samples with high mechanical properties comparable to those of high-strength alloys such as Ti6Al4V. The results showed that the fine nanoparticles significantly enhanced the strength of the material, while in several cases the material exceeded the values of the Ti6Al4V alloy. The produced sample exhibited a maximum compressive yield strength (1492 MPa), contained 10 wt.% of fine (milled) particles (average particle size: 3 μm) and was sintered at 900 °C for one hour.
1 June 2017 in Archives of Metallurgy and Materials
This work represents an interesting development in the detection and interpretation of crack evolution in through hole technology (THT) solder joints, which based on the development of general and common method. Serial sectioning is a useful method because it overcomes the problems associated with traditional two-dimensional metallographic techniques by providing information about (micro)structures in three-dimensions.In our work, serials sectioning with reconstruction method was utilized to visualize the 3D nature of cracks in through hole solder joint. Accurate quantitive analysis of the cracks, such as crack length, position and extension are presented with a help of the developed method: newly defined parameter and serial-cross sectioning method.
Hydroxyapatite (HAP) is the main inorganic component of mammal bone and teeth. It is one of the few bioactive materials, which helps cell growing. The objective of this study was to fabricate hydroxyapatite-biopolimer nanofiber mats. To achieve this goal, two different suspensions were used. Approximately 1 μm diameter size fibers with large HAP agglomerates were fabricated using acetone and acetic acid. Fibers with a larger diameter size and homogenous distributed HAP particles were produced applying acetone and isopropanol. During the experiment the effect of the processing parameters: applied voltage, diameter of needle, the distance of the needle tip and the collector, flow rate was analyzed.
12 October 2020 in Crystal Research and Technology