Konrad Kamieniecki

Dr. Konrad Kamieniecki

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 January 2022 in Energies
Verified
Journal Article
Open access
PDF file
JPJanusz Piechna
Janusz Piechna
KKKrzysztof Kurec
Krzysztof Kurec
JBJakub Broniszewski
Jakub Broniszewski
MRMichał Remer
Michał Remer
APAdam Piechna
Adam Piechna
PBPrzemysław Bibik
Przemysław Bibik
In the case of road cars, road safety is the primary factor. The geometry of high-speed road cars has no regulatory restrictions. In addition to the high engine power and effective shape, they can use various types of additional movable aerodynamic elements to adjust their aerodynamic characteristics to the road conditions. Based on the geometry of a two-seater prototype of such a vehicle, a numerical analysis of the influence of a number of additional movable aerodynamic elements on its aerodynamic characteristics was performed. Several of them were installed on the prototype. An electronic system recording a number of motion parameters of the entire car body and some of its movable elements installed on the body was designed and built. The system has been adapted to program the motion of additional aerodynamic elements according to the set algorithms of their activation, temporarily changing the aerodynamic characteristics of the car. An experimental study of the effect of changes in the aerodynamic characteristics of the prototype on its dynamic properties during a drive through a test road section was carried out. It was shown to what extent an average driver can increase the safe speed of the curve of the road using the possibilities of moving aerodynamic elements installed on it.

23 May 2017 in PLOS ONE
Verified
Journal Article
Open access
PDF file
MKMonika Kwacz
Monika Kwacz
MSMagdalena Sołyga
Magdalena Sołyga
MMMaciej Mrówka
Maciej Mrówka
KKKonrad Kamieniecki
Konrad Kamieniecki
Piston-stapedotomy is the most common method for hearing restoration in patients with otosclerosis. In this study, we have experimentally examined a prototype of a new chamber stapes prosthesis. The prototype was implanted in a human cadaver temporal bone. The round window vibrations before and after implantation were measured for the acoustic signal (90 dB SPL, 0.8–8 kHz) in the external auditory canal. In comparison with a 0.4-mm piston prosthesis, the chamber prosthesis induced significantly higher vibration of the round window, especially for frequencies above 1.5 kHz. Based on the results, it can be surmised that stapedotomy with a chamber stapes prosthesis could provide better hearing results in comparison with the piston-stapedotomy.

30 July 2022 in Energies
Verified
Journal Article
Open access
PDF file
MSMaciej Szudarek
Maciej Szudarek
KKKonrad Kamieniecki
Konrad Kamieniecki
STSylwester Tudruj
Sylwester Tudruj
JPJanusz Piechna
Janusz Piechna
Generating aerodynamic downforce for the wheels on the front axle of a car is a much more difficult task than for the rear axle. This paper, submitted to the special issue of Energies “Future of Road Vehicle Aerodynamics”, presents an unusual solution to increase the aerodynamic downforce of the front axle for cars with covered wheels, with the use of an elastic splitter. The effect of the inflatable splitter on the aerodynamic forces and moments was studied in a DrivAer passenger car and a fast sports car, Arrinera Hussarya. Providing that the ground clearance was low enough, the proposed solution was successful in increasing the front axle downforce without a significant increase in drag force. The possibility of emergency application of such a splitter in the configuration of the body rotated by up to 2 degrees with the front end raised was also analyzed. An elastic, deformed splitter remained effective for the nonzero pitch case. The results of the calculations are presented in the form of numerical data of aerodynamic forces, pressure and velocity distributions, and their comparisons. The benefits of the elastic splitter are documented, and the noted disadvantages are discussed.

16 January 2022 in Energies
Verified
Journal Article
Open access
PDF file
KKKrzysztof Kurec
Krzysztof Kurec
KKKonrad Kamieniecki
Konrad Kamieniecki
JPJanusz Piechna
Janusz Piechna
The purpose of this study was to investigate whether small plates covering the roof and the hood of the DrivAer estate vehicle can be used as airbrakes and increase its drag as well as the downforce. The presented results were obtained with the use of the commercial computational fluid dynamics software ANSYS® Fluent. The main findings of the article are that the aerodynamic devices such as flaps covering surfaces of the vehicle can have a significant impact on drag increase and can be used not only to make the design of the car more striking but also beneficial when utilized as a part of an active aerodynamic setup.

5 January 2025 in Electronics
Verified
Journal Article
Open access
PDF file
EJElżbieta Maria Jarzębowska
Elżbieta Maria Jarzębowska
Edyta Ładyżyńska-KozdraśEdyta Ładyżyńska-Kozdraś
Edyta Ładyżyńska-Kozdraś
KKKonrad Kamieniecki
Konrad Kamieniecki
The paper addresses the dynamics modeling of underwater vehicles that are inertia propelled, i.e., they can move based upon the change of the amount of water in their water tanks and the motion of an internal mass, enabling maneuvers. Underwater vehicles of this type can be successfully applied in ocean scientific reconnaissance and exploration missions or for water pollution monitoring. Usually, dynamics modeling methods for them are based upon the Newton–Euler or Lagrange approaches modified to encompass variable mass. The main motivation of this research is to explore other modeling methods and compare them to those traditionally used. In this paper, modeling methods based on the Maggi and Boltzmann–Hamel approaches are presented and discussed with respect to their effectiveness in modeling, operation, and control applications. The resulting comparisons indicate that the traditional approaches are sufficient for the analysis of vehicle operation and performance in the realization of simple tasks; however, they become of limited application when the variable mass or constraints on vehicle dynamics or motion are added or complex maneuvers are required. In this regard, the Maggi or Boltzmann–Hamel approaches are more effective for dynamics modeling. The theoretical development is illustrated by examples of vehicle dynamics developed using the approaches we propose.

18 November 2018 in Computer Methods in Biomechanics and Biomedical Engineering
Verified
Journal Article
Closed access
EKEmilia Anna Kiryk
Emilia Anna Kiryk
KKKonrad Kamieniecki
Konrad Kamieniecki
MKMonika Kwacz
Monika Kwacz
This paper presents the process of designing a new elastic element replacing a membrane in the chamber stapes prosthesis (ChSP). The results of the study are volume displacement characteristics obtained for the prosthesis and physiological stapes. Simulation tests on a 3D CAD model have confirmed that a properly designed ring can stimulate perilymph with the same or greater efficacy as the physiological stapes footplate placed on the elastic annular ligament. The ChSP with a new elastic element creates a good chance of improving hearing in patients suffering from otosclerosis.