The aim of this work is the development of the lattice Boltzmann model for simulation of the mold filling process. The authors present a simplified approach to the modeling of liquid metal-gas flows with particular emphasis on the interactions between these phases. The boundary condition for momentum transfer of the moving free surface to the gaseous phase is shown. Simultaneously, the method for modeling influence of gas back pressure on a position and shape of the interfacial boundary is explained in details. The problem of the lattice Boltzmann method (LBM) stability is also analyzed. Since large differences in viscosity of both fluids are a source of the model instability, the so-called fractional step (FS) method allowing to improve the computation stability is applied. The presented solution is verified on the bases of the available reference data and the results of experiments. It is shown that the model describes properly such effects as: gas bubbles formation and air back pressure, accompanying liquid-gas flows in the casting mold. At the same time the proposed approach is easy to be implemented and characterized by a lower demand of operating memory as compared to typical LBM models of two-phase flows.
18 April 2016 in Journal of Thermal Analysis and Calorimetry
TG–DSC thermal analysis involved two new BioCo foundry binders in the form of a composition with poly(acrylic acid) and modified polysaccharides (dextrin, sodium salt of carboxymethyl starch). Thermal analysis was conducted to determine the effect of the thermal decomposition conditions and polymer structure on the progress of degradation in terms of processes occurring in the foundry sands, when they contact with liquid metal. Thermal analysis of the composition allowed for determining the temperature range where they do not undergo degradation, by which they do not lose their binding properties. It was evidenced that the course of thermal decomposition is complex (mixed degradation mechanism). With temperature increase, physical and chemical changes occur, related to evaporation of solvent water (20–100 °C) and next release of constitution water, while finally intermolecular dehydration (100–220 °C). In this temperature range, mainly reversible processes take place. Within the temperature range of 220–300 °C, polymer chains decompose, including decomposition of side chains and glycosidic bonds. Within the temperature range of 300–500 °C, polymer compositions decompose, and gas products of destruction are generated. A part of the compound that did not decompose at the temperature of approx 550 °C can contain carbonised coal. It was evidenced that if the composition includes sodium atoms, inorganic compounds are formed which decompose at the temperature of approx 800 °C.
The role of rare Earth metals in the improvement of the properties of metals and alloys has been analysed and described in multiple studies. Their effects on changes in microstructure and mechanical properties are most pronounced. This paper focuses on the beneficial effect of rare Earth metal oxides on the wear resistance of surface layers applied to castings intended for structural elements of machinery and equipment in mining and recycling. The experiment involved modifying prepared surfaces by adding CeO2, Y2O3, and La2O3. Hardness measurements, a scratch test, and tribological tests were performed under dry and fluid friction. The maximum wear track depth and track area were measured from the surface profile. To determine correlations between the results, exploratory data analysis was employed. Heatmaps were used to illustrate strong positive and negative interactions. The addition of oxides at increasing carbon content resulted in increased hardness, lower coefficient of friction, and reduced track area and maximum track depth. Strong negative interactions between the track area and maximum track depth were found. The differences resulting from the test conditions (fluid and dry friction) were discussed. This study demonstrated the suitability of exploratory data analysis for analysing research results and confirmed the improvement of modified surface wear resistance.
1 September 2013 in Archives of Metallurgy and Materials
Application of modern technological solutions, as well as the economic and ecological solutions, is for foundries one of the main aspects of the competitiveness on the market for castings. IT solutions can significantly support technological processes. This article presents neural networks with different structures that have been used to determine the moisture content of the moulding sand based on the moulding sand selected properties research results. Neural networks were built using Matlab software. Moulding sand properties chosen for quality control processes were selected based on wide previous results. For the proposed moulding sand properties, neural networks can be a useful tool for predicting moisture content. The structure of artificial neural network do not have a significant influence on the obtained results. In subsequent studies on the use of neural networks as an application to support the green moulding sand rebonding process, it must be determined how factors such as environmental humidity and moulding sand temperature will affect the accuracy of data obtained with the use of artificial neural networks.
1 September 2013 in Archives of Metallurgy and Materials
Technological knowledge is a collection of information from each stage of the casting production preparation process along with production data and quality control data. Knowledge and experience are the most important factors for the dynamic development of each foundry. Efficient archiving and management of technological knowledge, including computer simulations, is a critical part of building competitive advantage. Analysis of historical data allows for drawing the right conclusions, and guarantees improved quality of the final product. Effective enterprise management system, and technological knowledge management system in particular, is an indispensable tool for any innovative foundry. Simulation Process & Data Management is a new, dynamically-developing scientific field. Also in the foundry industry it is a very important step towards the management of casting simulation results.
1 August 2025 in Journal of Ecological Engineering
Due to climate change, among other factors, many countries are experiencing problems with water resources consumed by population, industry and agriculture. In addition to the implementation of water conservation, it may be necessary to use the process of water recovery from treated wastewater...