The purpose of the study was to analyze the influence of the quality class and the orthotropy of wood upon the sound absorption coefficient, the reflection and the impedance ratio of two species widely used for stringed musical instruments, namely spruce (Picea abies L. Karst) and maple (Acer pseudoplatanus L.). An impedance tube for the frequency range 100–6400 Hz was used in these experimental determinations. Knowing the influence of porosity and tortuosity on the acoustic absorption, these properties were also determined, as well as the sound reduction coefficient and the maximum values of the acoustic absorption coefficients in relation to frequency. The main results highlighted the differences between the anatomical quality class of the wood within each species, but also concerning the sound direction relative to the three main sections of wood, as an orthotropic material. The article highlights the acoustic performance parameters related to the frequency of the wooden material and its relationship to density, porosity and quality class. The results represent useful information for musical instruments manufacturers and more.

The purpose of this paper is to propose a method for testing the effect of varying the kerfing parameters, on the flexibilization of plywood panels for indoor applications. The evaluation was made by comparisons of the change in the MOE, MOR, and maximum deflection, between flexibilized and non-flexibilized specimens subjected to static bending tests based on EN 310. In order to prevent the problem of sliding from the supports occurring for the flexibilized specimens, the standard specimens were modified by adding a frame and subjecting to bending just their central rail. Framed specimens of poplar plywood, of 8 mm thick, were laser cut with a rigid central rail, taken as reference and with the flexible kerfed rail. These had lengths of the flexible area of 50, 70, 90, and 110 mm and with two dimensions of the kerfing pitch, 6 and 10 mm. Very good correlations were found for MOE, MOR, and maximum deflection with the length of the kerfed area, for both values of the kerf pitch, which proves the sensitivity of the proposed method to the changes in the input parameters. The method could further serve to mathematically model the flexibility of a kerfed plywood panel by selecting the appropriate input data.

This paper presents structures of timber-framed walls designed for passive houses, using natural and waste resources as insulation materials, such as wool, wood fibers, ground paper, reeds (Phragmites communis), and Acrylonitrile Butadiene Styrene (ABS) wastes. The insulation systems of stud walls composed of wool–ABS composite boards and five types of fillers (wool, ABS, wood fibers, ground paper, and reeds) were investigated to reach U-value requirements for passive houses. The wall structures were designed at a thickness of 175 mm, including gypsum board for internal wall lining and oriented strand board (OSB) for the exterior one. The testing protocol of thermal insulation properties of wall structures simulated conditions for indoor and outdoor temperatures during the winter and summer seasons using HFM-Lambda laboratory equipment. In situ measurements of U-values were determined for the experimental wall structures during winter time, when the temperature differences between outside and inside exceeded 10 °C. The results recorded for the U-values between 0.20 W/m²K and 0.35 W/m²K indicate that the proposed structures are energy-efficient walls for passive houses placed in the temperate-continental areas. The vapour flow rate calculation does not indicate the presence of condensation in the 175 mm thick wall structures, which proves that the selected thermal insulation materials are not prone to degradation due to condensation. The research is aligned to the international trend in civil engineering, oriented to the design and construction of low-energy buildings on the one hand and the use of environmentally friendly or recycled materials on the other.

This paper presents the investigations conducted on three types of fibre-reinforced epoxy-resin hybrid composites with different structures, manufactured using midrib long fibres of date palm (Phoenix dactylifera L.) and Calotropis procera fibres. The two types of fibres were formed into flat sheets, without adding other chemicals or resins, and employed as reinforcing layers in the structure of the multi-layered laminate composites. Three-layer and five-layer epoxy-reinforced laminates were manufactured from the sheets of date-palm fibres and Calotropis sheets bonded with laminar epoxy resin. Water resistance investigation and mechanical testing under tensile, bending and impact loads were conducted in the research in order to evaluate and compare the performance of the resulting composites. Emphasis was put on the effect of various factors, such as the type of reinforcement material and the number of plies in the laminate on the mechanical behavior of the composites. The interpretation of those results was supported by the stereo-microscopic investigation of the adhesion between the layers of the composites, and the vertical density profile (VDP), which showed the repartition of the density on the composite thickness depending on the layer material. The results of the mechanical performance of the composites showed lower values of tensile strength, tensile modulus of elasticity and impact resistance and an increase of water absorption (WA) and thickness swelling (TS) for the five-layer composites compared to the three-layer composites. Contrarily, the addition of Calotropis fibres improved the flexural strength and the flexural modulus of elasticity. The alkali treatment of the Calotropis fibres improved the mechanical performance of the composites compared to the ones made with untreated fibres, because of an apparent increase in cellulose content and free hydroxyl groups revealed by FTIR spectra.

Investigating the large number of various materials now available, some materials scientists promoted a method of combining existing materials with geometric features. By studying natural materials, the performance of simple constituent materials is improved by manipulating their internal geometry; as such, any base material can be used by performing millimeter-scale air channels. The porous structure obtained utilizes the low thermal conductivity of the gas in the pores. At the same time, heat radiation and gas convection is hindered by the solid structure. The solution that was proposed in this research for obtaining a material with porous structure consisted in perforating extruded polystyrene (XPS) panels, as base material. Perforation was performed horizontally and at an angle of 45 degrees related to the face panel. The method is simple and cost-effective. Perforated and simple XPS panels were subjected to three different temperature regimes in order to measure the thermal conductivity. There was an increase in thermal conductivity with the increase in average temperature in all studied cases. The presence of air channels reduced the thermal conductivity of the perforated panels. The reduction was more significant at the panels with inclined channels. The differences between the thermal conductivity of simple XPS and perforated XPS panels are small, but the latter can be improved by increasing the number of channels and the air channels’ diameter. Additionally, the higher the thermal conductivity of the base material, the more significant is the presence of the channels, reducing the effective thermal conductivity. A base material with low emissivity may also reduce the thermal conductivity.

The present paper is part of an ongoing research project carried out to find methods to transpose traditional motifs from Romanian textile heritage to furniture ornamentation, as an additional method of preserving the motifs besides conventional conservation. Modern technology, such as Computer Numerical Control (CNC) routing or laser engraving can revive furniture ornamentation, eliminating manual labor and long execution time. Three methods were applied to transpose a bicolored motif from a traditional Romanian blouse from Transylvania onto the surface of maple wood furniture. The first method utilized was nitrogen laser engraving, in which ten power settings between 10 W and 150 W were applied and color measurements were carried out on the resulting engraved surfaces. Following the International Commission on Illumination (CIELab) system analysis, two laser power settings were selected to engrave the ornament on a maple wood surface for an accurate reproduction. The second method employed a staining solution applied on flat wood surface, followed by routing the model on a CNC machine and further coating with lacquer. The third method consisted of CNC routing the model on the wood surface, then coloring the engraved ornament followed by surface sanding to remove color from the flat wood surface and, finally, lacquering. The ornaments transposed onto maple wood surfaces were aesthetically assessed, the technologies were analyzed, and the details of the processed ornaments were highlighted by Stereo Microscope investigation. The conclusions showed that each method adds value to the wood surface by original ornamentation and can be applied as furniture decoration.