One of the most common failures or breakdowns that can occur in high-voltage (HV) equipment is due to partial discharges (PDs). This occurs as a result of inadequate insulation, aging, harsh environmental effects, or manufacturing flaws. PD detection and recognition methods have gained growing attention and have seen great progress in the past decades. Radiometric methods are one of the most investigated detection approaches due to their immunity to electromagnetic interference (EMI) and their capabilities to detect and locate PD activities in different applications such as transformers, cables, etc. Several review articles have been published to classify and categorize these works. Nonetheless, some concepts are missing, and some improvement techniques, such as PD detection at high-frequency (HF) and very high-frequency (VHF), have been overlooked. We present in this paper an exhaustive review study of state-of-the-art PD detection based on radiometric methods at different usable radiofrequency bands (i.e., HF, VHF, and UHF). Accordingly, we propose a new generic categorization approach based on the detected electromagnetic wave component (magnetic or electric fields) and pick-up location, either from free space or ground cable.

In this paper, a pioneer partial discharge (PD) loop antenna sensor is presented and examined. It is made of a 70-turn square planar inductor with a side length of 1.8 mm, which is fabricated on top of a silicon substrate in complementary metal oxide semiconductor technology. The microsensor ability to detect corona PD is demonstrated once connected in series with a 60 dB gain amplifier. The behavior is studied at different separation distances from the line through which the PD pulses flow. At 5 cm away, a damped sinusoidal induced voltage with an amplitude of about 100 mV has been measured. The output signal spectrum is highly concentrated around a central resonance frequency of ∼5 MHz. The microsensor response is compared with those of other industrial sensors from Techimp, i.e., horn antennas and high-frequency current transformer sensors. The presented on-chip sensor can be considered a non-intrusive competing solution compared with other heavy and expensive commercial sensors due to its lightweight, compact size, and low cost. In addition, it shows an acceptable signal to noise ratio compared with other commercial electromagnetic wave-based sensors.

In this study, different planar inductor topologies were studied to evaluate their characteristic parameters’ variation range upon approaching Fe- and Cu-based shield plates. The use of such materials can differently alter the electrical properties of planar inductors such as the inductance, resonant frequency, resistance, and quality factor, which could be useful in multiple devices, particularly in inductive sensing and radio-frequency (or RF) applications. To reach an optimal design, five different square topologies, including spiral, tapered, non-spiral, meander, and fractal, were built on a printed circuit board (PCB) and assessed experimentally. At the working frequency of 1 MHz, the results showed a decrease in the inductance value when approaching a Cu-based plate and an increase with Fe-based plates. The higher variation range was noticeable for double-layer topologies, which was about 60% with the Cu-based plate. Beyond an intrinsic deflection frequency, the inductance value began to decrease when approaching the ferromagnetic plate because of the ferromagnetic resonance (FMR). It has been shown that the FMR frequency depends on the inductor topology and is larger for the double-layer spiral one. The Q-factor was decreasing for all topologies but was much faster when using ferromagnetic plates because of the FMR, which intensely increases the track resistance. The resonant frequency was increasing for all double-layer topologies and decreasing for single-layer ones, which was mainly due to the percentage change in the stray capacitance compared to the inductance variation. The concept of varying inductors by metal shielding plates has great potential in a wide range of nondestructive sensing and RF applications.

In vivo biomedical devices are one of the most studied applications for vibrational energy harvesting. In this paper, we investigated a novel high-displacement device for harvesting heartbeats to power leadless implantable pacemakers. Due to the location peculiarities, certain constraints must be respected for the design of such devices. Indeed, the total dimension of the system must not exceed 5.9 mm to be usable within the leadless pacemakers and it must be able to generate accelerations lower than 0.25 m/s2 at frequencies of less than 50 Hz. The proposed design is an electrostatic system based on a square electret of dimension 4.5 mm. It is based on the Quasi-Concertina structure, which has a very low resonant frequency of 26.02 Hz and a low stiffness of 0.492 N/m, allowing it to be very useful in such an application. Using a Teflon electret charged at 1000 V, the device was able to generate an average power of 10.06 μW at a vibration rate of 0.25 m/s2 at the resonant frequency.