By their unique compositions and microstructures, recently developed high-entropy materials (HEMs) exhibit outstanding properties and performance above the threshold of traditional materials. Wear- and erosion-resistant materials are of significant interest for different applications, such as industrial devices, aerospace materials, and military equipment, related to their capability to tolerate heavy loads during sliding, rolling, or impact events. The high-entropy effect and crystal lattice distortion are attributed to higher hardness and yield stress, promoting increased wear and erosion resistance in HEMs. In addition, HEMs have higher defect formation/migration energies that inhibit the formation of defect clusters, making them resistant to structural damage after radiation. Hence, they are sought after in the nuclear and aerospace industries. The concept of high-entropy, applied to protective materials, has enhanced the properties and performance of HEMs. Therefore, they are viable candidates for today’s demanding protective materials for wear, erosion, and irradiation applications.
In this study, we designed and fabricated NbTiAlSiZrNx high-entropy alloy (HEA) films. The parameters of the radio frequency (RF) pulse magnetron sputtering process were fixed to maintain the N2 flux ratio at 0%, 10%, 20%, 30%, 40%, and 50%. Subsequently, NbTiAlSiZrNx HEA films were deposited on the 304 stainless steel (SS) substrate. With an increasing N2 flow rate, the film deposited at a RN of 50% had the highest hardness (12.4 GPa), the highest modulus (169 GPa), a small roughness, and a beautiful color. The thicknesses of the films were gradually reduced from 298.8 nm to 200 nm, and all the thin films were of amorphous structure. The electrochemical corrosion resistance of the film in a 0.5 mol/L H2SO4 solution at room temperature was studied and the characteristics changed. The HEA films prepared at N2 flow rates of 10% and 30% were more prone to corrosion than 304 SS, but the corrosion rate was lower than that of 304 SS. NbTiAlSiZrNx HEA films prepared at N2 flow rates of 20%, 40%, and 50% were more corrosion-resistant than 304 SS. In addition, the passivation stability of the NbTiAlSiZrNx HEA was worse than that of 304 SS. Altogether, these results show that pitting corrosion occurred on NbTiAlSiZrNx HEA films.
The rapid development of fusion-reactor technology calls for excellent anti-irradiation materials. Complex concentrated alloy (CCA) is a newly proposed alloy concept which is a promising candidate of nuclear fusion materials by virtue of its great phase stability under irradiation. This article summarizes anti-radiation mechanism and the microstructure evolution in HEAs. The effective factors on irradiation behavior of HEAs, including entropy, sample size and temperature, are discussed. Finally, the article introduces the potential ways to solve the economic and environmental problems which the HEAs faced for their applications in the future. In summary, the HEAs usually show better irradiation resistance than traditional alloys, such as less swelling, smaller size of defects, and more stable mechanical properties. One possible reason for the irradiation resistance of HEA is the self-healing effect induced by the high-entropy and atomic-level stress among the metal atoms. The activation of the principal element should be considered when selecting components of HEA, and the high throughput technique is a potential way to reduce the design and fabrication cost of HEAs. It is reasonable to expect that coming years will see the application of novel HEAs in fusion reactors.
In contrast to practical hot compression processes, the testing of the hot workability of TiAl alloys is usually conducted under the conditions of constant strain rates and constant temperatures. This work aims at investigating the microstructural evolution of TiAl alloys on a Gleeble-3800 thermomechanical simulator under a variable strain rate (0.1, 0.01 and 0.001 s−1) at 1200 °C. The results show that, after a holding time of 30 s, the abrupt change in the strain rate at ε = 0.3 (engineering strain) has a remarkable influence on the flow stress and dynamic recrystallization (DRX) behavior of the β-γ Ti-44Al-6Nb-1Mo-0.3 (B, Y, La, Ce) (at.%) alloy. The flow stress demonstrates a rapid decrease with a sudden reduction in the strain rate. A duplex microstructure of γ + B2/β can be obtained under a high strain rate or continuous medium strain rate. During the two-step deformation, however, both γ→α phase transformation and DRX exist, and the content of the α phase demonstrates a significant increase when the strain rate becomes lower. Finally, a fine-grained structure of γ + B2/β + α2 phases with low residual stresses can be obtained via the two-step heat treatment processes. This provides a promising approach to significantly improve the hot workability of β-γ TiAl alloys.