Indonesia has the third-largest motorcycle population in the world. These motorcycles have been known as a source of air pollution. Therefore, shifting the motorcycle to electric-driven based technology is inevitable. However, it is quite challenging as the residents prefer higher performance (in terms of power and speed) of the electric model which is unavailable in the market. Unfortunately, the demand for higher performance models creates other problems, such as the requirement for a bigger battery. This is because there is a range of anxiety phenomena in-vehicle usage. However, the capability to accurately estimate the electric motorcycle’s range does not exist. Therefore, this paper focuses on how to develop an electric scooter model to simulate its performances, especially its range estimation. The modeling approach was the use of an electric scooter longitudinal model developed in MATLAB/Simulink environment. Based on the dimensions and targeted performance, the developed model was simulated to determine its power and energy requirements. It is then validated using an experimental test on a dynamometer and on-road conditions. Based on the experimental data analysis, it can be concluded the developed model is valid and can be used as a basis for the next development of any electric motorcycle.
The R&D lead time of a motorcycle from scratch takes roughly five to seven years. This time frame needs to be significantly reduced to develop and produce an electric motorcycle in less than a year. The purpose of this article is to report the designing, testing, and mass production of GESITS, the first electric motorcycle developed in Indonesia. This was a significant development in Indonesian industries because motorcycles before GESISTS were developed by their principal engineers in Japan, India, or China. Due to the short time available for R&D, traditional methods employed by existing automotive industries were not applicable. They operated following the requirements from their motorcycle parent companies, which had gigantic markets, capabilities, and finance. Furthermore, the electric motorcycle industry was not yet ready because the R&D model seemed to be a push rather than pull market production employed by the existing industries. Therefore, a novel methodology and approaches for R&D and production are required. In terms of technology, business model, and company, this motorcycle was novel, meaning it was logical to implement the innovation-based approach to research, develop, and produce the GESITS. Lean start-up methodology governs the R&D process and was used to develop GESITS and its business model in less than two years. Subsequently, GESITS has been mass produced and sold in Indonesia and abroad with sales significantly increasing annually. Therefore, this article shows the successful implementation of the innovation-based concept in new industries—electrical motorcycles.
This paper discusses the process of developing a novel and robust algorithm for an interior permanent magnet synchronous motor controller. This is necessary for the simplification of the setting of control parameters and maintaining the proper operation of the motor. A 3D torque lookup table was used in which two inputs were considered, i.e., accelerator movements and the motor rotational speed. These two inputs allowed the lookup table to generate a specified torque at any motor rotation, which was then fed-forward to the field-oriented control and space vector pulse width modulation algorithm. Modeling, simulation, and experimental tests were performed to design and validate the proposed controller. The experimental validation shows that the proposed controller worked as intended. This was indicated by its ability to control the motor to obtain a 7% higher torque output than in the simulation in the constant torque region. In the field-weakening region, the controller could make the motor reach a maximum speed of 5500 RPM. There was only an 8% difference compared to the simulation (6500 RPM). In terms of maximum power generated, the controller was able to match the simulation output with only a 5% difference.
1 December 2022 in International Journal of Power Electronics and Drive Systems (IJPEDS)
Overheating is a failure mode that significantly affects the reliability of electronic devices. All electronic devices, including a 3-phase inverter driving a traction motor, produce heat dissipation. Heat dissipation needs to be controlled with cooling to prevent overheating. Overheating can be avoided by increasing cooling or reducing heat dissipation. Heat dissipation in the 3-phase inverter is caused by the internal resistance of the metal–oxide–semiconductor field-effect transistor (MOSFET), switching loss, and other factors. Cooling for the 3-phase inverter can use water coolant or air coolant. The cooling system is based on the amount of heat dissipation produced. Cooling of a 3-phase inverter can use air coolant with the addition of an extended surface area in the heat sink. The heat sink uses aluminum material, often called pin fin. There are kinds of aluminum available in the market. We calculated heat generation based on the MOSFET's internal resistance, switching loss, and other factors. We validated the simulation results experimentally using a thermal camera. Thus, we could find an optimal number, dimensions, and aluminum type of fin for the cooling system in the 3-phase inverter.
17 June 2025 in Jurnal Layanan Masyarakat (Journal of Public Services)
This community service program is implemented in an island region that has limited access to electricity and fuel. This program is implemented on Gili Iyang Island, Sumenep, Madura. On the island, the only mode of transportation available is motorbikes and three-wheeled motorbikes due to limited and narrow roads. The price of gasoline reaches two to four times the normal price. Based on these conditions, the issue raised in this community service program is the use of electric bicycles for mobility, with the hope that it can also be a means of supporting the main tourist attraction of the island known as "Oxygen Island". This program is training for the community on how to assemble and maintain electric bicycles. The electric bicycles used in this program are designed with compact and flexible advantages, equipped with lithium batteries with a range of up to 30 km. In addition, there is a pedal assist feature to make it easier to pedal when needed, such as when going uphill or crossing sandy roads. For recharging electric bicycles, a solar shelter is provided, which helps save transportation costs. Training is provided through theoretical and practical materials. Participants can directly implement the theory that has been conveyed when practicing assembling bicycles. Based on the results of the pre and post tests, in general, there was an increase of 17-50% in the knowledge and skills of participants related to the assembly and maintenance of electric bicycles. This is a very strong belief that the Gili Iyang community has been able to use and maintain electric bicycles.
8 December 2024 in Jurnal Layanan Masyarakat (Journal of Public Services)
This article discusses community service activities on Gili Iyang Island, Sumenep, Madura, which focus on implementing appropriate technology in sensing the potential of renewable energy sources. Gili Iyang Island itself is an area that actively encourages the use of renewable energy. In this activity, maintenance and monitoring of data on AirFeel are carried out, including device checks and monitoring data accuracy levels through periodic calibration. Airfeel is used as a weather station to measure the potential of renewable energy, especially wind and solar energy. The potential for wind energy is considered from the speed and direction of the wind, while the potential for solar energy is considered from the level of solar irradiation. These parameters allow Airfeel to determine the optimal location for renewable energy generation based on weather conditions. Additionally, the DJI Phantom 4 Pro RTK drone was used for 3D Mapping Photogrammetry. This technology aids in creating three-dimensional maps that are considered in the planning and development of renewable energy power plants at the location. Implementing these two technologies can contribute to future planning for developing other renewable energy sources in Gili Iyang Island.