In this paper, a novel heterostacked tunnel FET (HS-TFET) is proposed for steeper average subthreshold swing (SS). Different from conventional TFETs, HS-TFETs owns a stacked source configuration consisting of an upper source layer with a relatively larger bandgap material and an underlying source layer with smaller bandgap materials. Since smaller bandgap materials exhibit much higher band-to-band tunneling efficiency, the underlying layer of HS-TFET could provide extra drain current increment with increasing gate voltage, and thus effectively improve the subthreshold characteristics for steeper average SS. The simulation results show that the proposed Si-Ge-based HS-TFET can achieve much steeper average SS (25 mV/decade) than conventional Si TFET (42 mV/decade), exhibiting more than one decade higher I60 without leakage current degradation.
AlGaN/GaN high-electron-mobility transistors (HEMTs) with Hr0.5Zr0.5O2 ferroelectric gate stacks exhibiting significant ferroelectric switching for threshold voltage control are experimentally demonstrated. Ferroelectric gate HEMTs (FeHEMTs) with large threshold voltage tuning range of 2.8 V were obtained, with an on/off ratio of ~10 5 based on a GaN-channel HEMT structure suitable for RF applications. Improved subthreshold performance has also been achieved compared to conventional MIS-HEMTs, with reduction in average sub-threshold swing (SSavg) by a factor of 2. As a consequence of the significant ferroelectric polarization achieved on AlGaN/GaN heterostructures, Hr0.5Zr0.5O2 based ferroelectric gate AlGaN/GaN HEMTs appear promising for nonvolatile and reconfigurable RF and microwave applications.
In this letter, a novel hetero-stacked TFET (HS-TFET) is experimentally demonstrated and optimized for the first time, which can effectively suppress the subthreshold slope (SS) degradation without leakage current increase through self-adaptively current replenishing with bandgap engineering, greatly alleviating the critical issue of high average SS in conventional TFETs. Based on CMOS-compatible technology, the fabricated HS-TFETs of vertically stacked Si-Si 1-x Ge x source can experimentally achieve superior performance with nearly constant SS over five decades of drain current, high Ion (~14μA/μm @ VDS = -1 V), and large I on /I off ratio (~10 7 ). The proposed device with high process compatibility shows great potentials for future ultra-low power applications.
In this letter, a novel graded-channel heterojunction tunnel field-effect transistor (GCH-TFET) is proposed and studied by simulation. The novel TFET adopts a near broken-gap heterojunction at the source/channel interface to enhance the tunnel efficiency. Besides, it employs a graded component channel which works as an electron barrier to block up the leakage current at the OFF-state and can be removed with the increased gate voltage at the ON-state for high ON/OFF-current (I ON /I OFF ) ratio. Such graded channel also allows a sudden turn-on of band-to-band tunneling, resulting in a reduced sub-threshold swing (SS) compared with conventional heterojunction TFETs. The GCH-TFET demonstrates an I ON /I OFF ratio of more than seven decades with I ON up to 225 μA/μm at V DD = 0.3 V, I OFF more than two decades lower than a near broken-gap heterojunction TFET and SS lower than 30 mV/decade for more than five decades, exhibiting excellent potential for ultra-low power applications.
A systematic study of the selective etching of p-GaN over AlGaN was carried out using a BCl3/SF6 inductively coupled plasma (ICP) process. Compared to similar chemistry, a record high etch selectivity of 41:1 with a p-GaN etch rate of 3.4 nm/min was realized by optimizing the SF6 concentration, chamber pressure, ICP and bias power. The surface morphology after p-GaN etching was characterized by AFM for both selective and nonselective processes, showing the exposed AlGaN surface RMS values of 0.43 nm and 0.99 nm, respectively. MIS-capacitor devices fabricated on the AlGaN surface with ALD-Al2O3 as the gate dielectric after p-GaN etch showed the significant benefit of BCl3/SF6 selective etch process.
The effect of the source/drain compressive stress on the mechanical stability of stacked Si nanosheets (NS) during the process of channel release has been investigated. The stress of the nanosheets in the stacking direction increased first and then decreased during the process of channel release by technology computer-aided design (TCAD) simulation. The finite element simulation showed that the stress caused serious deformation of the nanosheets, which was also confirmed by the experiment. This study proposed a novel channel release process that utilized multi-step etching to remove the sacrificial SiGe layers instead of conventional single-step etching. By gradually releasing the stress of the SiGe layer on the nanosheets, the stress difference in the stacking direction before and after the last step of etching was significantly reduced, thus achieving equally spaced stacked nanosheets. In addition, the plasma-free oxidation treatment was introduced in the multi-step etching process to realize an outstanding selectivity of 168:1 for Si0.7Ge0.3 versus Si. The proposed novel process could realize the channel release of nanosheets with a multi-width from 30 nm to 80 nm with little Si loss, unlocking the full potential of gate-all-around (GAA) technology for digital, analog, and radio-frequency (RF) circuit applications.