We report on an optical setup to generate multi-Bessel beam profiles combining a refractive axicon and a spatial light modulator. Based on their particular beam profile, Bessel beams offer advantageous properties for micro drilling processes and internal volume processing, especially for transparent materials. In addition, the laser power of industrial, ultrashort pulsed lasers has increased significantly over the last few years, offering the possibility for highly efficient processes using multi-spot profiles. Our optical concept combines the dynamic possibilities of beam splitting using a spatial light modulator with the benefits of Bessel beams, which facilitates multi-Bessel beam processing. Beside the simulation and experimental evaluation of the generated multi-Bessel beams, we exemplify the applicability of the developed module for the perforation of thin metal foils by micro drilling.
We report on laser drilling borehole arrays using ultrashort pulsed lasers with a particular focus on reducing the inadvertent heat accumulation across the workpiece by optimizing the drilling sequence. For the optimization, evolutionary algorithms are used and their results are verified by thermal simulation using Comsol and experimentally evaluated using a thermal imaging camera. To enhance process efficiency in terms of boreholes drilled per second, multi-spot approaches are employed using a spatial light modulator. However, as higher temperatures occur across the workpiece when using simultaneous multi-spot drilling as compared to a single-spot process, a subtle spatial distribution and sequence of the multi-spot approach has to be selected in order to limit the resulting local heat input over the processing time. Different optimization approaches based on evolutionary algorithms aid to select those drilling sequences which allow for the combination of a high efficiency of multi-spot profiles, a low-generated process temperature and a high-component quality. In particular, using a 4 × 4 laser spot array allows for the drilling of 40,000 boreholes in less than 76 s (526 boreholes/s) with a reduced temperature increase by about 35%, as compared to a single spot process when employing an optimized drilling sequence.
We report on an optimization study of percussion drilling thin metal sheets employing a high repetition rate, high power femtosecond laser with respect to the resulting heat accumulation. A specified simplex algorithm was employed to optimize the spatial drilling sequence, whereas a simplified thermal simulation using COMSOL was validated by comparing its results to the temperature measurements using an infrared camera. Optimization for drilling borehole matrices was aspired with respect to the generated temperature across the processed specimen, while the drilling strategy was altered in its spatial drilling sequence and by using multi-spot approaches generated by a spatial light modulator. As a result, we found that an optimization strategy based on limited consecutive holes in a Moore neighborhood led to reduced temperatures and the shortest process times.
We report on the capability of an ultrasonic sensor, consisting of a membrane-free optical microphone, to distinguish material transitions in ultrashort pulsed laser ablation of multilayer material systems for electronic applications. The acoustic emission during the ablation of printed circuit board materials is used to detect the material transitions via specific acoustic signatures, thus enabling layer detection in the ablation process. Due to a higher removal rate in polyimide as compared to copper an increase of acoustic energy at the material transition between the copper and polyimide layers results, which enables layer detection, this process event can be used for process control. Membrane-free optical microphones have outstanding properties in terms of high temporal resolution and high bandwidth, making them suitable sensors for monitoring ablation processes using ultrashort pulsed lasers. In detail, different levels of the emitted acoustic energy during the ablation of copper and polyimide layers in multilayer materials are analyzed in different frequency ranges via the acoustic signal in order to realize a material-selective ablation control, which represents a novelty in the field of monitoring ultrashort pulsed laser multilayer ablation processes. In addition to the layer detection of different materials, the presented investigations also illustrate the specific signatures of the emitted acoustic energy of ablation processes as a function of the layer thickness and its spatial emitting properties across the scanning field.
We report on a novel approach for the monitoring of tangential laser turning with ultrashort laser pulses. By using an ultra-sonic sensor consisting of a membrane-free optical microphone, the current state of the ablation process can be analyzed, potentially enabling a real-time automated regulation. With its high sensitivity, bandwidth, and sampling rate, it is an ideal tool for process monitoring. The material ablation caused by focused femtosecond laser pulses produces distinct sound waves, which can be detected by the optical microphone. The diameter reduction of a rotating cylindrical workpiece during the laser turning process with ultrashort laser pulses results in a variation in the acoustic emissions. From this, properties like the state of the machining progress can be inferred.