Due to the recent surge in silicon demand for solar modules, thin-film photovoltaic (PV) modules have a potential to penetrate the market in significant numbers. As an alternate candidate, thin film technologies in PVs have the ability to achieve better performance. The competing thin-film PV technologies have the flexibility to adapt to any sort of curvature compared to rigid solar cells (SCs). Due to the peculiar characteristics of newer solar materials, stability issues, reflection losses, advancements in electrode materials and dopant materials with a photoactive layer are current challenges driving the industrial-academic voyage of development of solar materials for the betterment of Photo-conversion Efficiency (PCE). Based on the photoactive materials used over time, SC evolution was broadly classified into first, second and third generation SCs. In this review, the basic working mechanisms, various materials used, drawbacks and stability issues of different SCs are discussed extensively. Thin film SCs tend to absorb certain elastic deformations due to their flexible nature and to a certain extent. According to the NREL efficiency chart, multi-junctional SCs exhibit enhanced efficiency as compared to the other SCs. Among the third-generation SCs, the perovskite/Si tandem architecture shows a maximum efficiency of approximately 29%. Thin film flexible SCs find application in various sectors such as automobile, defense and/or energy storage devices

Hybrid energy systems (HESs) consisting of both conventional and renewable energy sources can help to drastically reduce fossil fuel utilization and greenhouse gas emissions. The optimal design of HESs requires a suitable control strategy to realize the design, technical, economic, and environmental objectives. The aim of this study is to investigate the optimum design of a grid-connected PV/battery HES that can address the load requirements of a residential house in Iraq. The MATLAB Link in the HOMER software was used to develop a new dispatch strategy that predicts the upcoming solar production and electricity demand. A comparison of the modified strategy with the default strategies, including load following and cycle charging in HOMER, is carried out by considering the techno-economic and environmental perspectives. According to optimization studies, the modified strategy results in the best performance with the least net present cost (USD 33,747), unmet load (87 kWh/year), grid purchases (6188 kWh/year), and CO₂ emission (3913 kg/year). Finally, the sensitivity analysis was performed on various critical parameters, which are found to affect the optimum results on different scales. Taking into consideration the recent advocacy efforts aimed at achieving the sustainable development targets, the models proposed in this paper can be used for a similar system design and operation planning that allow a shift to more efficient dispatch strategies of HESs.

Solar stills are one of the low water production desalination systems, but its low yield makes it necessary to investigate different design and performance parameters to improve its productivity. This paper aims to perform a parametric analysis of a solar still desalination system and study the effect of different absorber materials on the performance of a single-slope solar desalination unit employing computational fluid dynamics (CFD) numerical simulation via COMSOL^® Multiphysics software. To consider the absorptivity of water with different absorbing materials, simulation was conducted with the application of effective emissivity for the solar still walls. In addition, the economic, exergoeconomic, and CO₂ mitigation of solar stills were studied. The results revealed that the hourly water output of the solar desalination unit, with different absorbing materials (black ink, black dye, and black toner), reached the maximum values at 1:00 PM. On comparing the simulation results of solar stills with and without absorbing materials, it has been observed that the solar still painted with black toner shows the highest improvement in hourly productivity, the exergy of evaporation, and evaporative heat transfer coefficient with a maximum increase in respective values by 10.52%, 13.68% and 5.37%. The CO₂ mitigation and enviroeconomic parameter of the solar still using black toner were equal to 31.4 tons and 455.3 USD, respectively. Moreover, the lowest cost per liter (CPL) of the solar still was obtained using black toner, which was about 0.0066 USD/L.

Apart from being emission-free, electric vehicles enjoy benefits such as low maintenance and operating costs, noise-free, easy to drive, and the convenience of charging at home. All these benefits are directly dependent on the performance of the battery used in the vehicle. In this paper, one-dimensional modeling of Li-ion and NiMH batteries was developed, and their performances were studied. The performance characteristics of the batteries, such as the charging and discharging characteristics, the constituent losses of over-potential voltage, and the electrolyte concentration profile at various stages of charge and discharge cycles, were also studied. It is found that the electrolyte concentration profiles of Li-ion batteries show a drooping behavior at the start of the discharge cycle and a rising behavior at the end of discharge because of the concentration polarization due to the low diffusion coefficient. The electrolyte concentration profiles of NiMH batteries show rising behavior throughout the discharge cycle without any deviations. The reason behind this even behavior throughout the discharge cycle is attributed to the reduced concentration polarization due to electrolyte transport limitations. It is found that the losses associated with the NiMH battery are larger and almost constant throughout the battery’s operation. Whereas for the Li-ion batteries, the losses are less variable. The electrolyte concentration directly affects the overpotential losses incurred during the charging and discharging phases.

Solar desalination is a sustainable approach to producing fresh water from saline water. Researchers have tried modifications to solar desalination systems to enhance the distillate output. This survey aims to recognize the characteristics of research work for investigating solar desalination systems. The essential terms to be focused on are computational fluid dynamics (CFD) and solar radiation consideration for the investigation. The data for this bibliometric study was taken from Scopus, with 1932 publications. The characteristics of the research work were analyzed by identifying the research publications, research subject areas, journals, most contributed countries, and data from the authors. The research trend was investigated utilizing yearly research growth, geographical contributions, source quality of publications, and participation of various institutions. VOSviewer software was used for network analysis of essential keywords used in relevant research works and to understand collaborations between the authors and co-authors. About 76% of the total publications belong to the document type articles. It illuminates research tendencies related to the topic under consideration. Results show that desalination research work concerned with CFD or solar radiation was mainly investigated in Engineering and Environmental Science, with their share of more than 50% of the total publications. Further study of relevant research works was assessed using network analysis that helped to link different keywords and authors’ collaborations. This survey helps to spot the increasing research trends and the necessity of further research.