We have studied the radiation damage in diamond as a function of layer depth upon self-ion implantation with 9-MeV carbon ions and its recovery after annealing at 1000◦C. Raman and photoluminescence spectra show substantial damage of the lattice, namely, amorphization, neutral vacancies, and interstitial defects. Damage is maximum in the stopping layer at a depth of 4 μm. After annealing there is some recovery of the lattice, but the residual damage increases with fluence, up to about 2×10^16 ions/cm2. At this fluence the stopping layer becomes highly disordered and does not heal with annealing. Surprisingly, for higher fluence values, of about 5×10^16 ions/cm2, there is almost no residual damage. After full amorphization is reached, the layers appear to recrystallize by solid phase epitaxy (SPE), using the pristine diamond layers underneath as a template. These results prove that graphitization of diamond after annealing can be avoided in deeply buried layers, implanted at fluences much higher than expected. High fluences, in fact, can lead to high quality diamond layers. If SPE can be confirmed, it would have a great interest for diamond device applications, as it allows for higher doping levels.We thank the technical staff of CMAM for operating the tandem ion-beam accelerator. Funding: This work was supported by the Ministerio de Economía y Competitividad (MINECO), Spain [MAT2014-57547-R, MAT2014-54826-C2-1-R, FIS2014-54498-R, and CTQ-2014-53334-C2-2-R], the María de Maeztu Program for Units of Excellence in R&D [MDM-2014-0377], and the Comunidad Autónoma de Madrid [NANOFRONTMAG-CM (S2013/MIT-2850)].Peer reviewe
Concerning diamond-based electronic devices, the H-terminated diamond surface is one of the most used terminations as it can be obtained directly by using H2 plasma, which also is a key step for diamond growth by chemical vapour deposition (CVD). The resultant surfaces present a p-type surface conductive layer with interest in power electronic applications. However, the mechanism for this behavior is still under discussion. Upward band bending due to surface transfer doping is the most accepted model, but has not been experimentally probed as of yet. Recently, a downward band bending very near the surface due to shallow acceptors has been proposed to coexist with surface transfer doping, explaining most of the observed phenomena. In this work, a new approach to the measurement of band bending by angle-resolved X-ray photoelectron spectroscopy (ARXPS) is proposed. Based on this new interpretation, a downward band bending of 0.67 eV extended over 0.5 nm was evidenced on a (100) H-terminated diamond surface.
Silicon oxide atomic layer deposition synthesis development over the last few years has open the route to its use as a dielectric within diamond electronics. Its great band-gap makes it a promising material for the fabrication of diamond–metal–oxide field effects transistor gates. Having a sufficiently high barrier both for holes and electrons is mandatory to work in accumulation and inversion regimes without leakage currents, and no other oxide can fulfil this requisite due to the wide diamond band-gap. In this work, the heterojunction of atomic-layer-deposited silicon oxide and (100)-oriented p-type oxygen-terminated diamond is studied using scanning transmission electron microscopy in its energy loss spectroscopy mode and X-ray photoelectron spectroscopy. The amorphous phase of silicon oxide was successfully synthesized with a homogeneous band-gap of 9.4 eV. The interface between the oxide and diamond consisted mainly of single- and double-carbon-oxygen bonds with a low density of interface states and a straddling band setting with a 2.0 eV valence band-offset and 1.9 eV conduction band-offset.
18 October 2021 in IEEE Transactions on Electron Devices
Schottky contacts have been used to fabricate normally- OFF lateral reverse-blocking MESFETs on p-type (boron-doped) O-terminated monocrystalline diamond. The devices utilized an ohmic source contact but both gate and drain contacts were Schottky in nature. Boron-doped p-channel diamond MESFETs reported to date display the less attractive normally- ON characteristics. Here, the normally- OFF transistor delivered a current level of ~1.5 $\mu $ Amm −1 at a negative ${V}_{\text {GS}}$ of 0.8 V and a transconductance ( ${g}_{m}$ ) of $16~\mu $ Smm −1 , measured at room temperature (RT); at a temperature of 425 K, these values rose to $\sim 70~\mu $ Amm −1 for ${I}_{\text {DS}}$ and a ${g}_{m}$ value of $260~\mu $ Smm −1 . In both cases, a negligible gate leakage current was measured with no breakdown apparent at the maximum field investigated here ( $3.7\times 10^{{5}}$ V/m −1 ). The Schottky gate demonstrates a well-behaved control of the channel even at higher temperatures. The high-temperature operation, normally- OFF behavior, and diamond’s inherent radiation hardness make this transistor promising for harsh environment applications.