This paper characterises the flexural properties of relatively slender structural members (beams) manufactured using a FDM-based 3D printer. The primary goal is to assess the influence of infill properties on flexural rigidity through a parametric investigation. Infill percentage, infill orientation, and member thickness provided the parametric variation. The beams were tested by three-point bending, free vibration, and buckling. The tests showed that flexural rigidity varied linearly with infill percentage over most of the range considered, but fell off quickly below 10% infill. The optimal infill percentage that maximised specific flexural rigidity (flexural rigidity to length density) of the beams was determined to be between 10% and 20%.
23 August 2018 in Structural Control and Health Monitoring
The significance of critical infrastructure systems in maintaining productivity is undeniable. However, such systems remain susceptible to external disturbances and cascading failures. Instead of operating independently, these physical systems, such as transportation and stormwater systems, form an interdependent system. This interdependence, particularly important during flooding, illustrates that the failure of a stormwater system can disrupt traffic networks. To explore the extent of such interdependency, this study investigates the transportation and stormwater networks in Norman, Oklahoma. Using network science theories and concepts of multilayered networks, this paper analyzes these systems, both individually and in combination. The study identifies closely located components in the road and stormwater networks using Moran's I spatial autocorrelation metric. Next, the connectivity of these networks is represented in a graph format to investigate the topological credentials (i.e., rank of relative importance) of the network components (i.e., water inlets, road intersections as nodes, and stormwater conduits, road segments as links). Moreover, such credentials further change by considering the weights of the network components (i.e., average daily traffic, water flow). The proximity-based connectivity considerations between these networks utilizing Moran's I significance score revealed a good indicator of spatial interdependency. When incorporating directionality, the multilayer network analysis highlights that highly central components tend to cluster spatially, unlike the undirected counterpart. The study also identifies vulnerable locations and network components in a combined network setting that differ from the networks in isolation. In doing so, the research reveals new insights governing the complex reliance of transportation systems on neighboring stormwater systems.
Rolling isolation systems (RISs) have been used extensively to protect bridges, buildings, and equipment from earthquake-induced ground and floor motions. RISs are attractive in a performance-based design context because horizontal acceleration design requirements may easily be met by adjusting the slope of the rolling surface. However, in the process of reducing horizontal accelerations, the isolator transmits vertical accelerations due to the pendulumlike motion. These vertical accelerations may exceed tolerable limits if left unchecked. In this study, the influence of the rolling surface profile on peak vertical accelerations is assessed through experiments and simulations. RISs with different radii of curvature are fabricated and then tested for a wide range of ground-motion frequencies and amplitudes. The experiments and simulations show that vertical accelerations are not negligible and should not be ignored in the design of RISs.
1 October 2020 in Journal of Engineering Mechanics
Apparent weakening is the softening of a structure’s apparent stiffness by adding negative stiffness to the overall system, which has the benefit of reducing the peak accelerations and base shears induced in the structure due to a seismic event. Apparent weakening is an elastic effect that does not reduce the main structural strength. To attain this behavior, negative stiffness can be introduced through the integration of negative stiffness devices. This study presents a novel smooth negative stiffness device (SNSD) consisting of cables, pulleys, and tension springs. A nonlinear mathematical model of the force-deflection behavior of the SNSD was developed and used to determine the optimal geometry for such a device. A prototype device was designed and fabricated for installation in a bench-scale experimental structure, which was characterized through static and dynamic tests. This paper also presents a numerical study on two other device configurations designed to achieve different force-deflection relations for use in an inelastic model building subject to a suite of historic and synthetic ground motions. In both the experimental prototype and the numerical study, the SNSDs successfully produced apparent weakening, effectively reducing accelerations and base shears of the structures.
5 June 2022 in Earthquake Engineering & Structural Dynamics