The issue of movement stability remains highly relevant considering increasing vehicle speeds. The evaluation of vehicle stability parameters and the modeling of specific movement modes is a complex task, as no universal evaluation criteria have been established. The main task in modeling car stability is an integrated assessment of the vehicle’s road interactions and identification of relationships. The main system affecting the vehicle’s road interaction is the suspension of the vehicle. Vehicle suspension is required to provide constant wheel to road surface contact, thus creating the preconditions for stability of vehicle movement. At the same time, it must provide the maximum possible body insulation against the effect of unevennesses on the road surface. Combining the two marginal prerequisites is challenging, and the issue has not been definitively solved to this day. Inaccurate alignment of the suspension and damping characteristics of the vehicle suspension impairs the stability of the vehicle, and passengers feel discomfort due to increased vibrations of the vehicle body. As a result, the driving speed is artificially restricted, the durability of the vehicle body is reduced, and the transported cargo is affected. In the study, analytical computational and experimental research methods were used. Specialized vehicle-road interaction assessment programs were developed for theoretical investigation. The methodology developed for assessing vehicle movement stability may be used for the following purposes: design and improvement of vehicle suspension and other mechanisms that determine vehicle stability; analysis of road spans assigned with characteristic vehicle movement settings; road accident situation analysis; design of road structures and establishment of certain operational restrictions on the road structures. A vehicle suspension test bench that included original structure mechanisms that simulate the effect of the road surface was designed and manufactured to test the results of theoretical calculations describing the work of the vehicle suspension and to study various suspension parameters. Experimental investigations were carried out by examining the vibrations of vehicle suspension elements caused by unevenness on the road surface.

Operation modes of rolling stock at mining enterprises are considered and analyzed. The justification of the need to replace it with a modern specialized electric locomotive for quarry railway transport, equipped with an asynchronous traction electric drive and an on-board energy storage system, is presented. The determination of the parameters and structure of the on-board energy storage system, based on the condition of power compensation with limited power consumption from the traction network and ensuring the autonomous movement of the electric locomotive, is considered. This study was carried out by modeling the processes of energy exchange in the traction system of an electric locomotive. The use of lithium cells and supercapacitors in energy storage is considered. Variants of the hybridization of energy storage were studied from the standpoint of minimizing the weight, size, and cost indicators. It was established that reducing the mass of the energy storage device, which includes lithium cells and supercapacitors, leads to an increase in the cost of one kilowatt-hour of energy storage capacity, which reduces the attractiveness of capital expenditures for the creation of such an energy storage device. Hybridization of the energy storage device by combining lithium cells of different types practically does not improve its weight, size, and cost indicators. The recommended option is a storage capacity of energy based on LTO elements, for which it is necessary to select elements in order to minimize weight, size, and cost indicators.

This paper deals with the analysis of the operating conditions of traction drives of the electric locomotives with asynchronous traction motors. The process of change of the catenary system voltage was found to have a stochastic character. The method of current controller synthesis based on the Wiener–Hopf equation was proposed to enable efficient performance of the traction drive control system under the condition of the stochastic nature of the catenary system voltage and the presence of interferences, when measuring the stator current values of the tractor motor. Performance simulation of the proposed current controller and the current controller used in the existing vector control systems of the traction drives used in the electric locomotives was implemented. The results of the performance simulation of the proposed current controller were compared with the performance of the current controller in existing vector control systems of the traction drives. The results are applicable to the design of vector control systems of traction drives in electric locomotives and to the study of the influence of performance of electric traction drives in electric locomotives on the quality indicators of the power supplied by the traction power supply system under the actual operating conditions of the locomotive.

Off-road vehicles and transportation are vital for agricultural economics, yet the transition to green energies is challenging. To make this transition easier, a tool that enables the testing of heavy-duty off-road vehicles in various scenarios was created. Based on the methods of the World Harmonized Transient Cycle (WHTC), a new Hybrid Operational Cycle (HOC) that reflects the features of agricultural work was created and applied in a graphical model simulation. This was a newly developed methodology. The cycle and the model were based on gathered research data. A numerical model of a medium-power tractor with an internal combustion engine and a series-hybrid setup was created, and simulations were performed in Matlab and AVL Cruise. Both diesel and hybrid vehicles were compared in terms of their power production, fuel consumption, and efficiency in fieldwork and transportation scenarios. The results showed that a series-hybrid transmission can achieve an efficiency similar to that of a tractor with a continuously variable transmission (CVT), but because it uses an electric powertrain, it still provides the opportunity to exploit energy regeneration during transportation and under low-load conditions. The designed model may also be used to develop control algorithms for hybrid drives and improve their efficiency.

Two trends could be observed in the evolution of road transport. First, with the traffic becoming increasingly intensive, the motor road infrastructure is developed; more advanced, greater quality, and more durable materials are used; and pavement laying and repair techniques are improved continuously. The continued growth in the number of vehicles on the road is accompanied by the ongoing improvement of the vehicle design with the view towards greater vehicle controllability as the key traffic safety factor. The change has covered a series of vehicle systems. The tire structure and materials used are subject to continuous improvements in order to provide the maximum possible grip with the road pavement. New solutions in the improvement of the suspension and driving systems are explored. Nonetheless, inevitable controversies have been encountered, primarily, in the efforts to combine riding comfort and vehicle controllability. Practice shows that these systems perform to a satisfactory degree only on good quality roads, as they have been designed specifically for the latter. This could be the cause of the more complicated car control and accidents on the lower-quality roads. Road ruts and local unevenness that impair car stability and traffic safety are not avoided even on the trunk roads. In this work, we investigated the conditions for directional stability, the influence of road and vehicle parameters on the directional stability of the vehicle, and developed recommendations for the road and vehicle control systems to combine to ensure traffic safety. We have developed a refined dynamic model of vehicle stability that evaluates the influence of tire tread and suspensions. The obtained results allow a more accurate assessment of the impact of the road roughness and vehicle suspension and body movements on vehicle stability and the development of recommendations for the safe movement down the road of known characteristics.

Positioning applications are very important in a variety of industrial processes, including automatic assembly. This paper proposes a technique for positioning applications that involves employing a platform subjected to planar oscillations along circular, elliptical, and complex trajectories. Dynamic and mathematical models of the motion of a part on the platform were developed to investigate the motion characteristics of the part. The research showed that when the platform was excited in two perpendicular directions by sinusoidal waves, different trajectories of the part’s motion could be obtained by controlling excitation parameters such as the frequencies and amplitudes of the waves and the phase shift between the waves. Furthermore, by adjusting these parameters, the average displacement velocity of the part could be controlled. The results demonstrate that the part can be moved in any direction at a given velocity and can be subjected to complex dense positioning trajectories. Therefore, such a platform can be applied in feeding, positioning, and manipulation tasks.