An analysis of the operating conditions of the traction drives of an electric rolling stock with asynchronous traction motors was conducted. In the process of operation, the electric traction drive with both direct torque control and vector control was found to possibly experience unstable modes, both in terms of power supply and load. The models of electric locomotive traction drives with asynchronous electric motors with either vector or direct torque control were adapted to account for the possible presence of the aforementioned operational factors. As a result of the modeling, the starting characteristics of the electric traction drives with different control systems were obtained both in the absence and in the presence of power supply and load disturbances. The following cases were investigated for the drive with vector and direct torque control in the absence of power supply and torque disturbances: drive output at the rated speed of rotation of the electric motor shaft; 10% reduction in the rated speed; 10% increase in the rated speed. The comparison of the results obtained has demonstrated that, at lower than nominal frequencies, the electric traction drive with direct torque control has higher accuracy in its regulation of the rotational speed and torque, lower power consumption from the power supply, lower torque overshooting, but a higher level of torque pulsations than the electric traction drive with vector control. Meanwhile, at higher than nominal frequencies, the vector control has higher accuracy in its regulation of the speed, lower torque overshooting, shorter duration of transient processes, and lower torque pulsations than the direct torque control. Moreover, as a result of the investigations, the traction drive with direct torque control has been found to be more resistant to power supply and load disturbances. The results of this work are applicable to the investigation of the influence of electric traction drive control methods on the energy efficiency of the traction drive of an electric locomotive with an alternating current (AC).

Operation modes of rolling stock at mining enterprises are considered and analyzed. The justification of the need to replace it with a modern specialized electric locomotive for quarry railway transport, equipped with an asynchronous traction electric drive and an on-board energy storage system, is presented. The determination of the parameters and structure of the on-board energy storage system, based on the condition of power compensation with limited power consumption from the traction network and ensuring the autonomous movement of the electric locomotive, is considered. This study was carried out by modeling the processes of energy exchange in the traction system of an electric locomotive. The use of lithium cells and supercapacitors in energy storage is considered. Variants of the hybridization of energy storage were studied from the standpoint of minimizing the weight, size, and cost indicators. It was established that reducing the mass of the energy storage device, which includes lithium cells and supercapacitors, leads to an increase in the cost of one kilowatt-hour of energy storage capacity, which reduces the attractiveness of capital expenditures for the creation of such an energy storage device. Hybridization of the energy storage device by combining lithium cells of different types practically does not improve its weight, size, and cost indicators. The recommended option is a storage capacity of energy based on LTO elements, for which it is necessary to select elements in order to minimize weight, size, and cost indicators.

This paper deals with the analysis of the operating conditions of traction drives of the electric locomotives with asynchronous traction motors. The process of change of the catenary system voltage was found to have a stochastic character. The method of current controller synthesis based on the Wiener–Hopf equation was proposed to enable efficient performance of the traction drive control system under the condition of the stochastic nature of the catenary system voltage and the presence of interferences, when measuring the stator current values of the tractor motor. Performance simulation of the proposed current controller and the current controller used in the existing vector control systems of the traction drives used in the electric locomotives was implemented. The results of the performance simulation of the proposed current controller were compared with the performance of the current controller in existing vector control systems of the traction drives. The results are applicable to the design of vector control systems of traction drives in electric locomotives and to the study of the influence of performance of electric traction drives in electric locomotives on the quality indicators of the power supplied by the traction power supply system under the actual operating conditions of the locomotive.

This article presents an analysis of the causes behind the development of asymmetric modes in a traction drive system that features direct torque control (DTC) of a rolling stock with asynchronous traction motors. The development of asymmetric modes in the traction drive system was found to be caused by the asymmetry of the supply voltage system, the asymmetry of the traction motor windings, and transient processes triggered by a change in the inverter supply voltage and variation in the traction motor load. At the same time, the asymmetric modes caused by the asymmetry of the feed voltage system and the windings of the traction motor are the emergency modes. The influence of the asymmetry of the feed voltage system and asymmetry of the windings of traction motor on the starting characteristics of the phase currents and flux linkages of the stator in the steady-state mode was investigated. In these cases, the ratio of the amplitudes of phase currents and flux linkages of the stator of different phases was found to be constant. The effect of a variation in the feed voltage and load acting on the motor shaft on the starting characteristics of phase currents and flux linkages of the stator was investigated in the case of absence of the emergency modes. In these cases, the ratio of the amplitudes of phase currents and flux linkages of the stator of different phases was found to not be constant. The amplitudes of the phase current and stator flux linkage were proposed as criteria for diagnosis and identification of asymmetric emergency modes. An algorithm and a structural scheme have been proposed for the diagnosis of emergency asymmetric modes in the traction drive system with direct torque control. Modifications to the traction drive system with direct torque control are suggested in order to diagnose the presence of faulty asymmetric modes and identify the damaged traction drive element.

The economy sectors of transport and agriculture are among the major contributors to environmental pollution. Certain environmental solutions are increasingly implemented in agriculture in order to reduce the pollution. Among these solutions are the...

Positioning applications are very important in a variety of industrial processes, including automatic assembly. This paper proposes a technique for positioning applications that involves employing a platform subjected to planar oscillations along circular, elliptical, and complex trajectories. Dynamic and mathematical models of the motion of a part on the platform were developed to investigate the motion characteristics of the part. The research showed that when the platform was excited in two perpendicular directions by sinusoidal waves, different trajectories of the part’s motion could be obtained by controlling excitation parameters such as the frequencies and amplitudes of the waves and the phase shift between the waves. Furthermore, by adjusting these parameters, the average displacement velocity of the part could be controlled. The results demonstrate that the part can be moved in any direction at a given velocity and can be subjected to complex dense positioning trajectories. Therefore, such a platform can be applied in feeding, positioning, and manipulation tasks.