This study investigates the aerodynamic performance of a co-flow jet (CFJ) airfoil with the objective of enhancing lift and reducing drag through active flow control. National Advisory Committee for Aeronautics 0018 airfoil was employed for the computational fluid dynamics (CFD) study. This work examines the effect of slot placement, coefficient of jet momentum, and CFJ metrics namely injection velocity, injection mass flow rate, and injection height on the variation of aerodynamic coefficients. Additionally, the tradeoff between aerodynamic coefficients and associated power consumption was investigated. The study indicates that positioning injection slots near regions of minimum static pressure on the upper surface of the leading edge increases the coefficient of lift and mitigates power consumption. A maximum improvement in lift coefficient up to 30% was achieved, while the stall margin increased by 25%. The findings also indicate that CFJ configurations with higher jet momentum coefficients exhibit an improvement in lift-to-drag ratios by approximately 40% with a 15% reduction in drag in comparison with those of conventional airfoil. This research underlines the transformative potential of CFJ technology in optimizing aerodynamic performance with minimal energy impact, suggesting promising applications for enhancing aircraft efficiency and sustainability.
Wire Electrical Discharge Machining (WEDM) is a specialized thermal machining process capable of accurately machining parts with varying hardness or complex shapes, which have sharp edges that are very difficult to be machined by the main stream machining processes. Selection of process parameters for obtaining higher cutting efficiency or accuracy in WEDM is still not fully solved, even with most up-to-date CNC wire EDM machine. It is widely recognised that Acoustic Emission (AE) is gaining ground as a monitoring method for health diagnosis on rotating machinery. The advantage of AE monitoring over vibration monitoring is that the AE monitoring can detect the growth of subsurface cracks whereas the vibration monitoring can detect defects only when they appear on the surface. This study outlines the optimization of titanium material using L16 design of experiment. Each experiment has been performed varying the process parameters like pulse-on time, pulse-off time, current and bed speed. Among different process parameters voltage and flush rate were kept constant. Molybdenum wire having diameter of 0.18 mm was used as an electrode. Simple functional relationships between the parameters were plotted to arrive at possible information on Electrode Wear (EW) and AE signals. But these simpler methods of analysis did not provide any information about the status of the electrode. Thus, there is a requirement for more sophisticated methods that are capable of integrating information from the multiple sensors. Hence, method like Artificial Neural Network (ANN) has been applied for the estimation of EW, AE signal strength, AE count and AE RMS. The ANN algorithm is designed to learn the process by training the algorithm with the experimental data. The experimental observations are divided into three sets: the training set, validation set and testing set. The training set is used to make the ANN learn the process and the testing set will check the performance of ANN. Different models can be obtained by varying the percentage of data in the training set and the best model can be selected from these, viz., 50%, 60% and 70%. The best model is selected from the said percentages of data. Estimation of the EW and AE signals parameters by ANN at 70% of data training set showed the best correlation with the measured value.
Aircrafts are susceptible to various types of static and dynamic loading. Calculation of these loads are of prime importance in order to ensure the safety of an aircraft. Fatigue load is one such type of load which has to be evaluated. This project work comprises of design and fatigue analysis of a wing structure when different materials are used. The wing is of rectangular planform and is designed using CATIA V5. In order to illustrate the importance of materials and spar cross section in determining the structural strength of a wing, two materials (Carbon Epoxy and S-2 Glass) and two spar cross sections (I- Section and Rectangular Section) are chosen for detailed analysis. Following this structural analysis is carried out on ANSYS R18.1 using the static structural module to obtain the Equivalent Von-Misses stress distribution, life, damage, factor of safety and fatigue sensitivity of the wing structure due to the application of load. From the results obtained it can be observed that composites have high strength to weight ratio comparatively and hence the stresses developed in such materials are lower. On changing the spar cross section the variation in the results are clearly visible. Thereby indicating the important role of selection of materials and structural cross section in determining the strength of an aircraft structure.