Restorations in dentistry must reproduce the aspect of the patient’s natural teeth and require non-toxicity, biocompatibility, and good mechanical properties in order to last longer. Restorations are permanently in contact with microbes that can adhere to and form biofilms. The purpose of this study was to determine the adhesion extent of Streptococcus mutans to polymethyl methacrylate (PMMA) resin base containing TiO₂ nanoparticles. To understand the adhesion of Streptococcus mutans on the modified resin-based surfaces, the following surface properties were measured: the roughness, contact angle, zeta potential and CIE color parameters. Evaluation of tensile stress performance in TiO2 modified PMMA showed that the maximum tensile stress of the modified PMMA resin decreases with an increasing amount of TiO₂ nanoparticles. The increasing amount of TiO₂ decreases the roughness and causes contact angles in the border between hydrophilic and hydrophobic surfaces. All the studied surfaces are negatively charged and added TiO₂ tends to increase the zeta potential. The addition of TiO₂ nanoparticles increases the lightness and decreases the intensity of the red and yellow color. The increasing addition of TiO₂ nanoparticles into PMMA increases the morphological change of bacterial cells.

Full and partial restorations in dentistry must replicate the characteristics of the patient’s natural teeth. Materials must have good mechanical properties and be non-toxic and biocompatible. Microbes, which can form biofilms, are constantly in contact with restorations. In this study, we investigate how well Candida albicans adheres to a polymethyl methacrylate (PMMA) resin base with gold (Au) nanoparticles. We synthesized Au nanoparticles and characterized them. The average size of Au nanoparticles embedded in PMMA was 11 nm. The color difference ΔE between PMMA and PMMA/Au composites was 2.7 and was still esthetically acceptable to patients. PMMA/Au surfaces are smoother and more hydrophilic than pure PMMA surfaces, and the isoelectric point of both types of surfaces was 4.3. Above the isoelectric point, PMMA/Au surfaces are more negatively charged than PMMA surfaces. The added Au nanoparticles decreased the tensile strength, while the hardness did not change significantly. Adhesion measurements showed that PMMA surfaces modified with Au nanoparticles reduced the extent of microbial adhesion of Candida albicans.

Apples have long been known for their beneficial effects on human health due to the presence of various bioactive compounds. It is therefore very important to understand the biophysical properties of apple cuticle that dictate apples’ storability and quality. The purpose of this work was to determine the roughness, hydrophobicity, surface potential, and color of various autochthonous and new apple cultivars. The surface roughness was measured by optical profilometer, hydrophobicity by tensiometer, zeta potential by electro kinetic analyser, and surface color by chroma meter. Measurements reveal that the new cultivar Elstar has the roughest surface while the autochthonous cultivar Crown Prince Rudolph has the lowest roughness. Under normal physiological conditions, all apple surfaces were negatively charged, with Wax apple having the lowest and Crown Prince Rudolph the highest values; most cultivars had an isoelectric point at around pH = 3. The surfaces of the new cultivars were slightly more hydrophobic than those of the autochthonous. We conclude that autochthonous and new apple cultivars differ in biophysical surface properties, which might impact transpiration, bacterial/fungi adhesion and, consequently, apple storage and shelf life potential.

The global cannabis market is continuously expanding and as a result, the cannabis industry demands new and improved agronomic cultivation practices to increase production efficiency of cannabidiol (CBD), which is valued for its therapeutic benefits. This study investigates the influence of three rootstock types on the survival rate, morphological parameters, and biochemical composition of cannabis: potentially dwarfing rootstocks (PDR), potentially vigorous rootstocks (PVR), and seedlings-as-rootstocks (SAR). Rootstocks were used for grafting two scion genotypes: ‘ScionII’ = chemotype II of industrial hemp, and ‘ScionIII’ = chemotype III of high CBD accumulating variety. Contrary to expectations, PVR and SAR did not outperform PDR on most of the measured variables. SAR showed the highest survival rate of the grafted cannabis plants (40–70%). The rootstock type had a statistically significant influence only on the bud compactness index in ‘ScionII’, with PDR being particularly noticeable. A comparative analysis of the ‘rootstock/scion’ combinations with their controls (non-grafted scions) revealed grafting’s substantial improvement in most traits. Specifically, PDR increased CBD content by 27% in ‘ScionIII’, inflorescence yield and CBD yield per plant increased by 71% and 84%, respectively, when SAR was used in ‘ScionII’. SAR showed to be the most effective rootstock type for CBD production. Our findings suggest grafting as a promising technique for optimizing cannabis’s agronomic and medicinal potential, highlighting the necessity for further research on its underlying mechanisms to refine production efficiency and quality.

Enamel demineralization, known as dental caries, is instigated by the bacterium Streptococcus mutans, which generates acid during carbohydrate metabolism. Among carbohydrates, sucrose is the most cariogenic and capable of biofilm formation. This study aimed to explore and comprehend Streptococcus mutans’ adherence to two prevalent dental material surfaces, i.e., a cobalt–chromium (Co-Cr) alloy and a resin-based composite, under the influence of various sucrose concentrations. To understand bacterial adhesion, the surfaces were characterized using profilometry, tensiometry, and surface charge measurements. Bacterial adhesion was evaluated using scanning electron microscopy and crystal violet dye methods. Results revealed that the composite surface exhibited greater roughness compared with the Co-Cr alloy surface. Both surfaces displayed hydrophilic properties and a negative surface charge. Bacterial adhesion experiments indicated lower bacterial adherence to the Co-Cr alloy than to the composite surface before the addition of sucrose. However, the introduction of sucrose resulted in biofilm development on both surfaces, showcasing a similar increase in bacterial adhesion, with the highest levels being observed at a 5% sucrose concentration in the bacterial suspension. In conclusion, the findings suggest sucrose-rich foods could facilitate bacterial adaptation despite less favorable surface characteristics, thereby promoting biofilm formation.

Small cellular particles (SCPs) are being considered for their role in cell-to-cell communication. We harvested and characterized SCPs from spruce needle homogenate. SCPs were isolated by differential ultracentrifugation. They were imaged by scanning electron microscope (SEM) and cryogenic transmission electron microscope (cryo TEM), assessed for their number density and hydrodynamic diameter by interferometric light microscopy (ILM) and flow cytometry (FCM), total phenolic content (TPC) by UV-vis spectroscopy, and terpene content by gas chromatography-mass spectrometry (GC-MS). The supernatant after ultracentrifugation at 50,000× g contained bilayer-enclosed vesicles whereas in the isolate we observed small particles of other types and only a few vesicles. The number density of cell-sized particles (CSPs) (larger than 2 μm) and meso-sized particles (MSPs) (cca 400 nm–2 µm) was about four orders of magnitude lower than the number density of SCPs (sized below 500 nm). The average hydrodynamic diameter of SCPs measured in 10,029 SCPs was 161 ± 133 nm. TCP decreased considerably due to 5-day aging. Volatile terpenoid content was found in the pellet after 300× g. The above results indicate that spruce needle homogenate is a source of vesicles to be explored for potential delivery use.