The global problem of microplastics in the environment is “inspiring” scientists to find environmentally friendly and economically viable methods to remove these pollutants from the environment. Advanced oxidation processes are among the most promising methods. In this work, the potential of Fenton, photo-Fenton, and Fenton-like processes for the degradation of microplastics from low-density polyethylene (LDPE), polypropylene (PP), and poly(vinyl chloride) (PVC) in water suspensions was investigated. The influence of three parameters on the efficiency of the degradation process was tested: the pH of the medium (3–7), the mass of added iron (10–50 times less than the mass of microplastics), and the mass of added H2O2 (5–25 times more than the mass of added iron). The effectiveness of the treatment was monitored by FTIR-ATR spectroscopy. After 60-min treatments, the PP microparticles were found to be insensitive. In the Fenton treatment of PVC and the photo-Fenton treatment of LDPE and PVC, changes in the FTIR spectra related to the degradation of the microplastics were observed. In these three cases, the treatment parameters were optimized. It was found that a low pH (3) and a high iron mass (optimal values were 1/12 and 1/10 of the mass of the microplastics for LDPE and PVC, respectively) favored all three. The degradation of LDPE by the photo-Fenton treatment was favored by high H2O2 concentrations (25 times higher than the mass of iron), while these concentrations were significantly lower for PVC (11 and 15 times for the Fenton and photo-Fenton treatment, respectively), suggesting that scavenging activity occurs.
In the last two decades, microplastics (MP) have been identified as an emerging environmental pollutant. Due to their small size, MP particles may easily enter the food chain, where they can have adverse effects on organisms and the environment in general. The common methods for the removal of pollutants from the environment are not fully effective in the elimination of MP; thus, it is necessary to find a more suitable treatment method(s). Among the various approaches tested, biodegradation is by far the most environmentally friendly and economically acceptable remediation approach. However, it has serious drawbacks, generally related to the rather low removal rate and often insufficient efficiency. Therefore, it would be beneficial to use some of the less economical but more efficient methods as pretreatment prior to biodegradation. Such pretreatment would primarily serve to increase the roughness and hydrophilicity of the surface of MP, making it more susceptible to bioassimilation. This review focuses on advanced oxidation processes (AOPs) as treatment methods that can enhance the biodegradation of MP particles. It considers MP particles of the six most commonly used plastic polymers, namely: polyethylene, polypropylene, polystyrene, polyvinyl chloride, polyethylene terephthalate and polyurethane. The review highlights organisms with a high potential for biodegradation of selected MP particles and presents the potential benefits that AOP pretreatment can provide for MP biodegradation.
The harmful effects of microplastics are not yet fully revealed. This study tested harmful effects of polyethylene (PE), polypropylene (PP), polystyrene (PS), polyvinyl chloride (PVC), and polyethylene terephthalate (PET) microplastics were tested. Growth inhibition tests were conducted using three microorganisms with different characteristics: Scenedesmus sp., Pseudomonas putida, and Saccharomyces cerevisiae. The growth inhibition test with Scenedesmus sp. is relatively widely used, while the tests with Pseudomonas putida and Saccharomyces cerevisiae were, to our knowledge, applied to microplastics for the first time. The influence of concentration and size of microplastic particles, in the range of 50–1000 mg/L and 200–600 µm, was tested. Determined inhibitions on all three microorganisms confirmed the hazardous potential of the microplastics used. Modeling of the inhibition surface showed the increase in harmfulness with increasing concentration of the microplastics. Particle size showed no effect for Scenedesmus with PE, PP and PET, Pseudomonas putida with PS, and Saccharomyces cerevisiae with PP. In the remaining cases, higher inhibitions followed a decrease in particle size. The exception was Scenedesmus sp. with PS, where the lowest inhibitions were obtained at 400 µm. Finally, among the applied tests, the test with Saccharomyces cerevisiae proved to be the most sensitive to microplastics.
Microplastics are an emerging class of recalcitrant organic pollutants that are of general scientific and public interest nowadays. It would be ideal to remove microplastics from the environment through biodegradation, as biodegradation is a highly ecological and economically acceptable approach. Unfortunately, the efficiency of biodegradation of conventional plastic polymers is low. The application of a suitable pretreatment could increase the efficiency of biodegradation. In this study, the applicability of UV-C/H2O2 and UV-C/S2O82− advanced oxidation processes as pretreatments for the biodegradation of polystyrene and poly(vinyl chloride) microplastics by the yeast Candida parapsilosis was investigated. For the investigated range (pH 4–10, peroxide concentration up to 20 mM and treatment duration up to 90 min), the UV-C/H2O2 process proved to be more effective in degrading polystyrene microplastics, while the UV-C/S2O82− process was more efficient at degrading poly(vinyl chloride) microplastics. Samples pretreated under optimal conditions (90 min treatment time at a pH of 5.7 and H2O2 concentration of 20.0 mM for polystyrene samples; 90 min treatment time at a pH of 8.6 and S2O82− concentration of 11.1 mM for poly(vinyl chloride) samples) were subjected to biodegradation by Candida parapsilosis. The biodegradation conditions included an agitation speed of 156 rpm and an initial pH of 5.7 for the experiments with the polystyrene samples, while an agitation speed of 136 rpm and an initial pH of 4.9 were used for the poly(vinyl chloride) experiments. The initial value of the optical density of the yeast suspension was 1.0 in both cases. The experiments showed a positive effect of the pretreatment on the number of yeast cells on the surface of the microplastics.
Biodegradation is the most environmentally friendly and, at the same time, economically acceptable approach to removing various pollutants from the environment. However, its efficiency in removing microplastics (MPs) from the environment is generally low. The successful biodegradation of MPs requires microorganisms capable of producing enzymes that degrade MP polymers into compounds that the microorganisms can use as a source of carbon and energy. Therefore, scientists are screening and characterizing microorganisms that can degrade MPs more efficiently. These microorganisms are often isolated from sites contaminated with MPs because the microorganisms living there are adapted to these pollutants and should be able to better degrade MPs. In this study, five bacterial strains and five yeast strains were isolated from various environmental samples including activated sludge, compost, river sediment, and biowaste. Among them, screening was performed for bacteria and yeasts with the highest potential for the biodegradation of polystyrene (PS) and polyvinyl chloride (PVC) MPs, and the bacterium Delftia acidovorans and the yeast Candida parapsilosis were identified as the best candidates. Optimization of biodegradation of the selected MPs by each of these two microorganisms was performed, focusing on the influence of cell density, agitation speed and pH of the medium. It was found that within the selected experimental ranges, high values of cell density, low agitation speed, and a slightly basic medium favored the biodegradation of PS and PVC MPs by Delftia acidovorans. In the case of Candida parapsilosis, favorable conditions also included high cell density followed by a slightly higher, but not maximum, agitation speed and a weakly acidic medium. Broad spectroscopic and imaging methods indicated that Delftia acidovorans and Candida parapsilosis better adapt to PVC MPs to use it as a carbon and energy source.
Antivirals are considered emerging environmental contaminants. Unfortunately, for many of these substances, there is limited information on their occurrence, fate, and behavior in the environment, which is essential for proper risk assessment. In this study, forced degradation tests were conducted on six widely used antivirals to assess their environmental fate. These antivirals were atazanavir, emtricitabine, nirmatrelvir, oseltamivir, ribavirin, and sofosbuvir. The tests included exposure of the antivirals to (artificial) sunlight, different temperatures, water, an acidic solution (1 M HCl), an alkaline solution (1 M NaOH) and a solution containing 30% H2O2 as a strong oxidizing agent. Liquid chromatography with UV detection (LC-UV) was used to analyze antivirals. To monitor the conversion, an LC-UV method was developed and validated for each antiviral. According to the results of the forced degradation tests, atazanavir and emtricitabine are probably the most unstable in the aquatic environment. Oseltamivir and sofosbuvir begin to lose stability even at slightly elevated temperatures, such as 40 °C. The stability of the tested antivirals depends strongly on the medium’s pH value and the presence of an oxidizing agent. Thus, all six antivirals showed some degree of degradation under the applied alkaline and oxidative conditions, while only emtricitabine, oseltamivir, and ribavirin remained stable under the applied acidic conditions.