This letter presents a novel tilt-rotor octocopter that can generate tiltable thrust without the need for servo-driven mechanisms. The octocopter's eight rotors are divided into pairs and each pair is mounted on an arm, which is connected to the airframe through passive hinges. Each pair is also equipped with a sub-controller that uses the differential thrust of the rotor pair to control the arm's tilting angle. Then, these sub-controllers work together with the main controller installed on the frame body to regulate the attitude and position of the octocopter. This octocopter can be controlled via a remote controller in a manner similar to a classic quadrotor, operating in stabilized or position mode both indoors and outdoors, also capable of executing flight missions following predefined trajectories. Considering that the communication delays between the main controller and sub-controllers would degrade the control performance due to the delayed response of the vectored thrust. We also propose a decentralized control allocation strategy that directly assigns parts of control loops to the sub-controllers so that the communication delays can be bypassed. Finally, we demonstrate the advantages of the new octocopter with the proposed method through simulations and real flight experiments.
Distributed electric propulsion technology has great potential and advantages in the development of drones. In this paper, to study the slipstream effect of distributed propellers, the actuator disk method was used to verify a single propeller, and the calculated thrust was in good agreement with the test results. Then, based on the actuator disk method, the influence of different installation positions on the slipstream effect was studied, and the distributed propeller layout was optimized by a genetic algorithm to improve the low-speed performance of the unmanned aerial vehicle (UAV) during the take-off phase and increase the cruise duration. The analysis results showed that the lift of the wing will be larger when the propellers are higher than the wing. The wing lift and drag of the counter-rotating are less than those of the co-rotating. Compared with the original layout, the lift coefficient of the optimized distributed propeller layout is significantly increased by 30.97%, while the lift/drag ratio is increased by 7.34%. Finally, we designed the test platform and qualitatively verified the calculated results without quantitative verification.
Fixed-wing Vertical Takeoff and Landing (VTOL) drones have been widely researched and applied because they combine the advantages of both rotorcraft and fixed-wing drones. However, the research on the transition mode of this type of drone has mainly focused on completing the process quickly and stably, and the application potential of this mode has not been given much attention. The objective of this paper is to routinize the transition mode of compound VTOL drones, i.e., this mode works continuously for a longer period of time as a third commonly used mode besides multi-rotor and fixed-wing modes, which is referred to as the hybrid mode. For this purpose, we perform detailed dynamics modeling of the drone in this mode and use saturated PID controllers to control the altitude, velocity, and attitude of the drone. In addition, for more stable altitude control in hybrid mode, we identify the relevant parameters for the lift of the fixed-wings and the thrust of the actuators. Simulation and experimental results show that the designed control method can effectively control the compound VTOL drone in hybrid mode. Moreover, it is proven that flight in hybrid mode can reduce the flight energy consumption to some extent.
29 January 2023 in IET Control Theory & Applications
Distributed electronic propulsion (DEP) aircraft with vertical take‐off and landing (VTOL) ability mostly equipped with multiple redundant tiltable propulsors, which are used to provide not only thrusts, but also control torque in all flight mode. The features make the control allocation problem of these aircraft both complex and important. Therefore, this paper proposes: (і) a prototype platform for DEP VTOL aircraft that allows researchers to design and analyse control allocation strategies, and (іі) a uniform hierarchical control allocation method that can be adapted to both MC and FW modes. The platform contains ten fully actuated thrusters, which are distributed in the scaled geometry of a typical DEP‐VTOL aircraft. The proposed control allocation strategy uses hierarchical structure to avoid high‐dimensional matrix operations for the redundant actuators. The additional constraints on the thrust and tilt angles of the actuators are addressed by adopting cascade generalized inversion (CGI) to force decompensation (FD)‐based methods by a coordinate transformation. A novel smooth strategy through Schur Complement is also presented to achieve steady and smooth transition from MC to FW mode. Finally, the proposed method is implemented in the authors’ novel platform in both simulations and flight experiments to demonstrate its effectiveness and smoothness.
31 January 2023 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
This paper presents a cascade-modified uncertainty and disturbance estimator (CMUDE)–based controller. The attitude-tracking performance of a quadrotor would be greatly degraded due to two factors: (1) a nonideal actuator and (2) an exogenous disturbance. Based on these factors, an actuator model is accurately identified using a thrust test platform. Then, a cascade-structured CMUDE controller is designed through the backstepping method, so the disturbances from different channels can be separately dealt with. The idea of the uncertainty and disturbance estimator (UDE) is then applied to dynamically compensate for not only the exogenous disturbance but also the time delay in the actuator dynamics. Benefitting from that, the problem of mismatched disturbances is solved by defining virtual control inputs; furthermore, the nonlinear term in the attitude kinematics is included in the model uncertainty to be canceled instead of being ignored. When tracking attitude commands, the exogenous disturbance and model uncertainty along with the time delay of the actuator are estimated and compensated for by the proposed controller, so the performance of the disturbance rejection is significantly improved while maintaining a quick response to the rapidly changing commands. To verify that, the proposed controller is implemented on a quadrotor platform to carry out exhaustive experiments and compared with the mainstream cascade PID (CPID) controller, the classic UDE-based controller, and the latest modified-UDE (MUDE)–based controller. The results show that our control strategy achieves a better disturbance rejection and more accurate tracking performance than other controllers.
15 July 2024 in IEEE Robotics and Automation Letters
This paper presents a novel control allocation compensator for a tilt-rotor octocopter using passive hinges, aimed at enhancing attitude control performance by accounting for the dynamic characteristics of the actuators. The introduction of a passive hinging mechanism results in a slower tilt angle response compared to servo-actuated systems, which, if overlooked, can significantly degrade controller performance. In this regard, the paper first models the arm's tilting dynamics and discusses its impact on control allocation errors. A two-part compensator is then introduced to address these dynamics: the first part adds a simple control loop to the control allocation module to quicken the tilt response; the second part re-allocates the thrust based on estimated tilt angles, leveraging the motor's rapid response to offset the slow response of the tilt angle. By simultaneously accelerating the tilt response and reallocating thrusts, the compensator minimizes control allocation error, thereby enhancing the accuracy of position and attitude control. The effectiveness of the proposed method is validated through both simulations and real flight experiments.