An assessment of the tritium (T) inventory in plasma facing components (PFC) during JET T and deuterium-tritium (DT) operations is presented based on the most comprehensive ex situ fuel retention data set on JET PFCs from the 2015-2016 ILW3 operating period is presented. The global fuel retention is 4.19 × 1023 D atoms, 0.19% of injected fuel. The inner divertor remains the region of highest fuel retention (46.5%). The T inventory in PFCs at the end of JET operations is calculated as 7.48 × 1022 atoms and is informative for accountancy, clean-up efficacy and waste liability assessments. The T accumulation rate at the upper inner divertor during JET DT operations has been used to assess the requirements and frequency of operation of a new laser induced desorption diagnostic to be installed on JET for the final DT experiments in 2023.
The ITER-Like-Wall project has been carried out at the Joint European Torus (JET) to test plasma facing materials relevant to ITER. Materials being tested include both bulk metals (Be and W) and coatings. Tritium accumulation mechanisms and release properties depend both on the wall components, their location in the vacuum vessel, conditions of exposure to plasma and to the material itself. In this study, bulk beryllium limiter tiles, plasma-facing beryllium coated Inconel components from the main chamber, bulk tungsten and tungsten coated carbon fibre composite divertor tiles were analysed. A range of methods have been developed and applied in order to obtain a comprehensive overview on tritium retention and behaviour in different materials of plasma facing components (PFCs). Tritium content and chemical state were studied by the means of chemical or electrochemical dissolution methods and thermal desorption spectroscopy. Tritium distribution in the vacuum vessel and factors affecting its accumulation have been assessed and discussed.
Sulfonated poly(ether ether ketone) (SPEEK) materials are promising candidates for replacing Nafion™ in applications such as proton exchange membrane (PEM) and direct methanol fuel cells. SPEEK membranes have several advantages such as low cost, thermal and radiation stability and controllable physicochemical and mechanical properties, which depend on the degree of sulfonation (DS). Commercial PEEK was homogenously sulfonated up to a DS of 60–90% and the membranes were prepared using a solvent casting method. Part of the samples were irradiated with a 10 MeV electron beam up to a 500 kGy dose to assess the ionizing radiation-induced effects. Both non-irradiated and irradiated membranes were characterized by Fourier Transformation infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA), proton nuclear magnetic resonance (1H-NMR) spectroscopy, electrochemical impedance analysis and, for the first time for non-irradiated membranes, by spectrophotometric analysis with Cr(III). The above-mentioned methods for application for DS assessment were compared. The aim of this study is to compare different methods used for the determination of the DS of SPEEK membranes before and after high-dose irradiation. It was observed that irradiated membranes presented a higher value of DS. The appearance of different new signals in 1H-NMR and FT-IR spectra of irradiated membranes indicated that the effects of radiation induced changes in the structure of SPEEK materials. The good correlation of Cr(III) absorption and SPEEK DS up to 80% indicates that the spectrophotometric method is a comparable tool for the characterization of SPEEK membranes.
In this study, a tritium enrichment system in the water phase has been developed based on the combination of a proton exchange membrane (PEM) electrolysis cell and a fuel cell. As the PEM, NafionTM and laboratory-synthesized sulfonated poly(ether ether ketone) membranes modified with an additional graphene layer in order to enhance the tritium separation factor were used. Both differences in the kinetics of the hydrogen evolution reaction and transport through the graphene layer of different isotopes are the driving factors expected to affect the separation of hydrogen isotopes. The separation factor was measured both during the electrolysis and fuel cell stage using different membranes. The facilitating effect of the graphene on the separation efficiency was determined during the study. The separation factor obtained by the proposed method was evidently higher than that obtained by other conventional methods.