This paper presents a data-driven kinematic model for the end-effector pose control applied to a variety of manipulator robots, focusing on the entire end-effector’s pose (position and orientation). The measured signals of the full pose and their computed derivatives, along with a linear combination of an estimated Jacobian matrix and a vector of joint velocities, generate a model estimation error. The Jacobian matrix is estimated using the Pseudo Jacobian Matrix (PJM) algorithm, which requires tuning only the step and weight parameters that scale the convergence of the model estimation error. The proposed control law is derived in two stages: the first one is part of an objective function minimization, and the second one is a constraint in a quasi-Lagrangian function. The control design parameters guarantee the control error convergence in a closed-loop configuration with adaptive behavior in terms of the dynamics of the estimated Jacobian matrix. The novelty of the approach lies in its ability to achieve superior tracking performance across different manipulator robots, validated through simulations. Quantitative results show that, compared to a classical inverse-kinematics approach, the proposed method achieves rapid convergence of performance indices (e.g., Root Mean Square Error (RMSE) reduced to near-zero in two cycles vs. a steady-state RMSE of 20 in the classical approach). Additionally, the proposed method minimizes joint drift, maintaining an RMSE of approximately 0.3 compared to 1.5 under the classical scheme. The control was validated by means of simulations featuring an UR5e manipulator with six Degrees of Freedom (DOF), a KUKA Youbot with eight DOF, and a KUKA Youbot Dual with thirteen DOF. The stability analysis of the closed-loop controller is demonstrated by means of the Lyapunov stability conditions.
In this study, the effects of Nb on the microstructural characteristics, hardness, and corrosion resistance of high-silicon ductile cast iron (HSDI)-3.6 wt.% Si were investigated. Samples from different castings with 0–0.9 wt.% Nb were obtained and compared to a commercial ductile iron. Microstructures showed that the amount of ferrite in the matrix increased with increasing Nb content, from 34% for unalloyed HSDI to 88% for HSDI-0.9 wt.% Nb. The presence of randomly distributed NbC carbides was identified by EDX for all the samples alloyed with Nb, and the hardness of the HSDI increased with the Nb content. To evaluate the influence of the Nb content on the corrosion resistance of HSDI, potentiodynamic tests were carried out in a solution of H2SO4. The highest corrosion rate on HSDI was obtained for the HSDI-0.3 wt.% Nb sample, with 2802 mills per year, due to the amount of pearlite present and the lowest presence of NbC carbides, compared to the HSDI-0.9 wt.% Nb, with 986 mills per year. This behavior was attributed to the ferrite matrix obtained because of a high Si content in the DI, which delayed the anodic dissolution of the alloy and suppressed the pearlitizing effect of Nb for contents greater than 0.3 wt.%, as well as to the effect of NbC carbides, which acted as inhibitors.
Industrial wastewater can be reused in other everyday processes to help combat water scarcity worldwide. One contaminant in industrial wastewater is hexavalent chromium, which is highly toxic and can cause kidney, liver, and respiratory problems, making its removal vital. In this study, PLA-based films containing modified zirconia nanoparticles were developed via a solution-mixing process for hexavalent chromium adsorption. Obtaining the films involved two stages: the first was the chemical modification of ZrO2 nanoparticles with thiamine hydrochloride (vitamin B1) using fixed-frequency ultrasound at an output of 750 W and 50% amplitude for 60 min. The second stage involved preparing the films by mixing them in the solution using an ultrasonic bath. The nanoparticle concentrations were 0.25, 0.5, and 1 wt%. The results obtained from characterization using Fourier-transform infrared spectroscopy (FT-IR) revealed the characteristic bands of PLA and the characteristic peak of the Zr-O bond corresponding to the ZrO2 nanoparticles. Thermogravimetric analysis (TGA) showed that the ZrO2 nanoparticles provided thermal stability to the PLA polymer. X-ray diffraction (XRD) showed a broad peak of amorphous PLA at 16.8° and signals corresponding to the crystalline phase of ZrO2. The morphology of a cross-section of the films was observed using scanning electron microscopy (SEM), revealing a rough surface with pores. Finally, hexavalent chromium adsorption tests were carried out, measuring the adsorption efficiency under the parameters of pH, concentration, and contact time. The PLAZrO2 sample achieved an adsorption efficiency of 83% at pH 2.
14 March 2024 in International Journal of Metalcasting
Ensuring repeatability in robotic manipulators is critical for industrial applications, particularly in cyclic tasks where precision and consistency are required. This study aims to establish the conditions that are necessary for repeatability in data-driven task-space control, compare repeatability across redundant robotic manipulators, and reduce the computational costs associated with data-based control methods compared to traditional model-based approaches. To achieve this, a large number of cyclic actions are simulated, mimicking real-world industrial routines. The methodology evaluates the estimated Jacobian matrix’s manipulability and its role in facilitating effective task execution within the operational space of the robot. The results demonstrate that the proposed approach achieves consistent repeatability at the full pose level of the end-effector, integrating both position and orientation. In particular, the findings indicate that the proposed controller minimizes variability and ensures reliable motion execution, even in the presence of system redundancies, as observed in the eight-DoF KUKA YouBot manipulator. These insights contribute to advancing data-driven control strategies for redundant robotic systems, enhancing their applicability in industrial settings.