Jesús Salvador Galindo Valdés

Prof. Jesús Salvador Galindo Valdés

Facultad de Ingeniería, Universidad Autónoma de Coahuila

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 December 2020 in Crystals
Verified
Journal Article
Open access
PDF file
Daniel GarciaDaniel Garcia
Daniel Garcia
JOJuan Carlos Ortiz-Cuellar
Juan Carlos Ortiz-Cuellar
Jesús Salvador Galindo ValdésJesús Salvador Galindo Valdés
Jesús Salvador Galindo Valdés
JCJosué Gómez Casas
Josué Gómez Casas
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
NRNelly Abigail Rodríguez Rosales
Nelly Abigail Rodríguez Rosales
Friction Stir Welding (FSW) is a feasible welding process to join dissimilar materials due to its solid-state nature. In this study the FSW of 6061-T6 aluminum with pure Cu plates was performed with the objective of evaluating the effects of the FSW parameters on the microstructure and electrical properties. The processing parameters (rotational and traverse speeds) were established to reduce the common defects in the friction-stir welding process. Therefore, the obtained results validated the better mechanical properties and a smaller increase of the electrical resistivity. The rotational speeds used were of 1000, 1150, and 1300 rpm, and the traverse speeds of 20, 40, and 60 mm/min, with the purpose of varying the heat input of the process. The microstructural characterization revealed the presence of a mixture of aluminum and copper into the weld zone, along with copper particles and the formation of intermetallic compounds. It was found that the electrical resistivity of the joints ranged from 0.029 to 0.036 μΩ. The highest electrical resistivity values were obtained at the lowest traverse speed (20 mm/min) and the lowest resistivity values were obtained at highest traverse speed (60 mm/min).

16 March 2021 in Crystals
Verified
Journal Article
Open access
PDF file
Félix MontesFélix Montes
Félix Montes
NRNelly Abigail Rodríguez Rosales
Nelly Abigail Rodríguez Rosales
JOJuan Carlos Ortiz-Cuellar
Juan Carlos Ortiz-Cuellar
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
JCJosué Gómez Casas
Josué Gómez Casas
OGOziel Gómez-Casas
Oziel Gómez-Casas
Friction stir welding is characterized as an ecological and low-cost process in comparison to traditional welding techniques, and due to its application in the solid state, it is a feasible option for joining similar and/or dissimilar materials. The present investigation seeks to determine the effect of friction stir welding’s parameters on the corrosion resistance of an Al 6061-T6–Cu C11000 dissimilar joint, with mathematical analysis to validate the results. After the welding process, the samples were exposed to a NaCl solution in an electrochemical cell to determine the corrosion rate via potentiodynamic tests. Microstructural characterization revealed a laminar structure, composed of aluminum and copper, as well as copper particles and the formation of intermetallic compounds distributed in the weld zone. The potentiodynamic tests showed that the corrosion rate increased with the rotational and traverse speeds. The mathematical model quantifies the relationship between corrosion rate and rotational and traverse speeds.

15 April 2022 in Metals
Verified
Journal Article
Open access
PDF file
NRNelly Abigail Rodríguez Rosales
Nelly Abigail Rodríguez Rosales
Félix MontesFélix Montes
Félix Montes
OGOziel Gómez-Casas
Oziel Gómez-Casas
JCJosué Gómez Casas
Josué Gómez Casas
Jesús Salvador Galindo ValdésJesús Salvador Galindo Valdés
Jesús Salvador Galindo Valdés
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
This research evaluates the effect of temperature and time austempering on microstructural characteristics and hardness of ductile iron, validating the results by means of a statistical method for hardness prediction. Ductile iron was subjected to austenitization at 950 °C for 120 min and then to austempering heat treatment in a salt bath at temperatures of 290, 320, 350 and 380 °C for 30, 60, 90 and 120 min. By increasing austempering temperature, a higher content of carbon-rich austenite was obtained, and the morphology of the thin acicular ferrite needles produced at 290 °C turned completely feathery at 350 and 380 °C. A thickening of acicular ferrite needles was also observed as austempering time increased. An inversely proportional behavior of hardness values was thus obtained, which was validated through data analysis, statistical tools and a regression model taking temperature and time austempering as input variables and hardness as the output variable, which achieved a correlation among variables of about 97%. The proposal of a mathematical model for the prediction of hardness in austempered ductile iron represents a numerical approximation which validates the experimental results at 95.20%.

24 September 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
JMJesús Fernando Martínez-Villafañe
Jesús Fernando Martínez-Villafañe
JOJuan Carlos Ortiz-Cuellar
Juan Carlos Ortiz-Cuellar
Jesús Salvador Galindo ValdésJesús Salvador Galindo Valdés
Jesús Salvador Galindo Valdés
FCFrancisco Cepeda
Francisco Cepeda
JCJosué Gómez Casas
Josué Gómez Casas
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
In this research, the effect of the interelectrode distance (d) in the electrocoagulation (EC) reactor was studied. The experiments were carried out with varying d in values of 3, 5, and 9 mm during the treatment of water contaminated with fluoride (F−). The response variables analyzed were the treatment time necessary to reduce the residual concentration of F− to 1.5 mg L−1, the number of aluminum hydroxides formed, the potential drop in the reactor terminals, and the electric power consumption of the reactor. The software FLUENT version 6.3 was employed to simulate the liquid velocity profiles achieved in the reactor chamber. The results obtained show that the liquid velocity increases in the interelectrode spaces to 0.48, 0.65, and 0.86 m s−1 for interelectrode distances of 9, 5, and 3 mm, respectively, which favors not only the formation of flocs but also the elimination of fluoride. With a shorter interelectrode distance, the EC reactor not only consumes less electrical energy but also fewer electrodes, and the dispersion of generated flocs in the reactor chamber is major, which is more important than the quantity of flocs generated in it.

9 May 2023 in Metals
Verified
Journal Article
Open access
PDF file
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
DNDaniel García Navarro
Daniel García Navarro
Jesús Salvador Galindo ValdésJesús Salvador Galindo Valdés
Jesús Salvador Galindo Valdés
Félix MontesFélix Montes
Félix Montes
ECEfrain Almanza Casas
Efrain Almanza Casas
NRNelly Abigail Rodríguez Rosales
Nelly Abigail Rodríguez Rosales
In this study, the effects of Nb on the microstructural characteristics, hardness, and corrosion resistance of high-silicon ductile cast iron (HSDI)-3.6 wt.% Si were investigated. Samples from different castings with 0–0.9 wt.% Nb were obtained and compared to a commercial ductile iron. Microstructures showed that the amount of ferrite in the matrix increased with increasing Nb content, from 34% for unalloyed HSDI to 88% for HSDI-0.9 wt.% Nb. The presence of randomly distributed NbC carbides was identified by EDX for all the samples alloyed with Nb, and the hardness of the HSDI increased with the Nb content. To evaluate the influence of the Nb content on the corrosion resistance of HSDI, potentiodynamic tests were carried out in a solution of H2SO4. The highest corrosion rate on HSDI was obtained for the HSDI-0.3 wt.% Nb sample, with 2802 mills per year, due to the amount of pearlite present and the lowest presence of NbC carbides, compared to the HSDI-0.9 wt.% Nb, with 986 mills per year. This behavior was attributed to the ferrite matrix obtained because of a high Si content in the DI, which delayed the anodic dissolution of the alloy and suppressed the pearlitizing effect of Nb for contents greater than 0.3 wt.%, as well as to the effect of NbC carbides, which acted as inhibitors.

2 June 2023 in Mathematics
Verified
Journal Article
Open access
PDF file
America MoralesAmerica Morales
America Morales
JCJosué Gómez Casas
Josué Gómez Casas
CTChidentree Treesatayapun
Chidentree Treesatayapun
Carlos rodrigo Muñiz ValdezCarlos rodrigo Muñiz Valdez
Carlos rodrigo Muñiz Valdez
Jesús Salvador Galindo ValdésJesús Salvador Galindo Valdés
Jesús Salvador Galindo Valdés
JMJesús Fernando Martínez-Villafañe
Jesús Fernando Martínez-Villafañe
Data technology advances have increased in recent years, especially for robotic systems, in order to apply data-driven modelling and control computations by only considering the input and output signals’ relationship. For a data-driven modelling and control approach, the system is considered unknown. Thus, the initialization values of the system play an important role to obtain a suitable estimation. This paper presents a methodology to initialize a data-driven model using the pseudo-Jacobian matrix algorithm to estimate the model of a mobile manipulator robot. Once the model is obtained, a control law is proposed for the robot end-effector position tasks. To this end, a novel neuro-fuzzy network is proposed as a control law, which only needs to update one parameter to minimize the control error and avoids the chattering phenomenon. In addition, a general stability analysis guarantees the convergence of the estimation and control errors and the tuning of the closed-loop control design parameters. The simulations results validate the performance of the data-driven model and control.