Colloidal quantum dots (CQDs), are a promising candidate material for realizing colored and semitransparent solar cells, due to their band gap tunability, near infrared responsivity and solution-based processing flexibility. CQD solar cells are typically comprised of several optically thin active and electrode layers that are optimized for their electrical properties; however, their spectral tunability beyond the absorption onset of the CQD layer itself has been relatively unexplored. In this study, we design, optimize and fabricate multicolored and transparent CQD devices by means of thin film interference engineering. We develop an optimization algorithm to produce devices with controlled color characteristics. We quantify the tradeoffs between attainable color or transparency and available photocurrent, calculate the effects of non-ideal interference patterns on apparent device color, and apply our optimization method to tandem solar cell design. Experimentally, we fabricate blue, green, yellow, red and semitransparent devices and achieve photocurrents ranging from 10 to 15.2 mA/cm2 for the colored devices. We demonstrate semitransparent devices with average visible transparencies ranging from 27% to 32%, which match our design simulation results. We discuss how our optimization method provides a general platform for custom-design of optoelectronic devices with arbitrary spectral profiles.
An optically pumped molecular laser system utilizing a transverse or zig-zag pumping geometry of the far-infrared (FIR) laser medium has enabled the reinvestigation of the CH2DOH, CHD2OH, and CH318OH isotopic forms of methanol for wavelengths > 100 μm. With this system, 28 FIR laser emissions have been discovered with wavelengths ranging from 117.2 to 744.7 μm. Along with the wavelength, each laser emission is reported with its optimal operating pressure, polarization with respect to the CO2 pump laser, and relative intensity. Three of the laser emissions generated by CH318OH support the spectroscopic assignments of FIR laser transitions originally proposed through combination-difference loops. A fourth CH318OH laser emission should contribute to another, incomplete FIR laser scheme.
We report long-cavity (60.5 λ) GaN-based vertical-cavity surface-emitting lasers with a topside monolithic GaN concave mirror, a buried tunnel junction current aperture, and a bottomside nanoporous GaN distributed Bragg reflector. Under pulsed operation, a VCSEL with a 9 µm aperture had a threshold current density of 6.6 kA/cm2, a differential efficiency of 0.7%, and a maximum output power of 290 µW for a lasing mode at 411 nm and a divergence angle of 8.4°. Under CW operation, the threshold current density increased to 7.3 kA/cm2, the differential efficiency decreased to 0.4%, and a peak output power of 130 µW was reached at a current density of 23 kA/cm2.
The optical and electrical characteristics of InGaN blue and green micro-light-emitting diodes (μLEDs) with GaN tunnel junction (TJ) contacts grown by metalorganic chemical vapor deposition (MOCVD) were compared at different activation temperatures among three activation methods from the literature, namely, sidewall activation, selective area growth (SAG), and chemical treatment before sidewall activation. The devices with chemical treatment before activation resulted in uniform electroluminescence and higher light output power, compared to the devices with sidewall activation and SAG. Moreover, the green μLEDs showed greater optical degradation at elevated activation temperatures, whereas the blue μLEDs yielded trivial difference with activation temperatures from 670 to 790 °C. The 5 × 5 μm2 devices with chemical treatment before activation and SAG yielded almost identical voltage at 20 A/cm2, and the voltage penalty significantly decreased with activation temperature in the case of devices with sidewall activation. The devices with chemical treatment before activation resulted in higher external quantum efficiency (EQE) and wall-plug efficiency (WPE) in low current density range compared to the devices with SAG. The enhancements in EQE and WPE were observed in different μLED sizes, suggesting that chemical treatment before sidewall activation enables the use of TJ contacts grown by MOCVD and is advantageous for applications that require high brightness and efficiency.
The electrical performances of III-nitride blue micro-light-emitting diodes (µLEDs) with different tunnel junction (TJ) epitaxial architectures grown by metalorganic chemical vapor deposition are investigated. A new TJ structure that employs AlGaN is introduced. The current density–voltage characteristic is improved by incorporating AlGaN layer above the n-side of the TJ layer, and the effects of the AlGaN/GaN superlattices is examined. Based upon the data from band diagram simulation, net positive polarization charge is formed at the AlGaN/GaN interface, which results in a reduction in tunneling distance and increase in tunneling probability. Moreover, similar electrical improvement is observed in various device dimensions and is independent of operating current density, suggesting that AlGaN/GaN biaxial tensile strain or current spreading is not the main contribution for the improvement. Finally, the effects on the efficiency performances are determined. While the maximum external quantum efficiency of the TJ devices remains identical, the wall-plug efficiency of µLEDs is enhanced significantly by the proposed AlGaN-enhanced TJ design. This work reveals the possibility of energy efficient TJ contact with high transparency in the visible wavelength range.