The generic wind turbine models developed in recent years by the International Electrotechnical Commission (IEC) and the Western Electricity Coordinated Council (WECC) are intended to meet the needs of public, standard, and relatively simple (small number of parameters and computational requirements) wind turbine and wind farm models used to conduct transient stability analysis. Moreover, the full-scale converter (FSC) wind turbine technology referred to as Type 4 by IEC and WECC, is increasingly used in current power systems due to its control benefits. Hence, the development of this generic model has become a priority. This study presents the validation of two generic Type 4 wind turbine models, which have been developed in accordance with the IEC and WECC guidelines, respectively. Field data collected from a real wind turbine located in a Spanish wind farm was used to validate both generic Type 4 wind turbine models following the IEC validation guidelines. Ten different test cases are considered, varying not only the depth and duration of the faults but also the load of the wind turbine. The parameters of the models were kept constant for all the simulation cases, aiming to evaluate the accuracy of the models when facing different voltage dips.

This paper analyzes the response under voltage dips of a Type 3 wind turbine topology based on IEC 61400-27-1. The evolution of both active power and rotational speed is discussed in detail when some of the most relevant control parameters, included in the mechanical, active power and pitch control models, are modified. Extensive results are also included to explore the influence of these parameters on the model dynamic response. This work thus provides an extensive analysis of the generic Type 3 wind turbine model and provides an estimation of parameters not previously discussed in the specific literature. Indeed, the International Standard IEC 61400-27-1, recently published in February 2015, defines these generic dynamic simulation models for wind turbines, but does not provide values for the parameters to simulate the response of these models. Thus, there is a pressing need to establish correlations between IEC generic models and specific wind turbine manufacturer models to estimate suitable parameters for simulation purposes. Extensive results and simulations are also included in the paper.

The widespread use of renewable energies around the world has generated the need for new tools and resources to allow them to be properly integrated into current power systems. Power system operators need new dynamic generic models of wind turbines and wind farms adaptable to any vendor topology and which permit transient stability analysis of their networks with the required accuracy. Under this framework, the International Electrotechnical Commission (IEC) and the Western Electricity Coordinating Council (WECC) have developed their own generic dynamic models of wind turbines for stability analysis. Although these entities work in conjunction, the focus of each is slightly different. The WECC models attempt to minimise the complexity and number of parameters needed, while the IEC approach aims to optimise comparison with real turbine measurements. This study presents a detailed comparison between these two different approaches for modeling a Type 3 (i.e., DFIG) wind turbine in MATLAB/Simulink. Finally, several simulations are conducted, with which the consequences of the different approaches are evaluated. The results of this paper are of interest to power system operators as well as wind turbine manufacturers who require further assistance in adapting their specific models to the simplified versions provided by the International Committees.

The calculation of short-circuit currents is critical for the design of protection systems and electrical equipment rating. The short-circuit current contribution of traditional synchronous generators, which depends on common machine parameters, has been validated in recent decades. In this sense, the increasing penetration of wind power generation in current power systems means that network operators need to evaluate the response of wind turbines when a fault occurs. The recent publication of Edition 2 of IEC 60909-0 in 2016 defined a formulation to represent the short-circuit contribution for modern wind turbines, such as doubly-fed and full-converter technologies. Nevertheless, both the IEC and the ANSI/IEEE guidelines are based on new parameters that must be provided by the wind turbine manufacturer. This paper develops a methodology to calculate the parameters that define the short-circuit contribution of doubly-fed wind turbines for both international guidelines, IEC 60909-0 Ed. 2 and ANSI/IEEE. Field measurements and simulations are used for the validation of the developed method. Furthermore, some of the shortcomings of the IEC short-circuit calculation method are identified and alternative approaches are proposed and evaluated.

Forecasts for 2023 position wind energy as the third-largest renewable energy source in the world. This rapid growth brings with it the need to conduct transient stability studies to plan network operation activities and analyze the integration of wind power into the grid, where generic wind turbine models have emerged as the optimal solution. In this study, the generic Type 3 wind turbine model developed by Standard IEC 61400-27-1 was submitted to two voltage dips and implemented in two simulation tools: MATLAB/Simulink and DIgSILENT-PowerFactory. Since the Standard states that the responses of the models are independent of the software used, the active and reactive power results of both responses were compared following the IEC validation guidelines, finding, nevertheless, slight differences dependent on the specific features of each simulation software. The behavior of the generic models was assessed, and their responses were also compared with field measurements of an actual wind turbine in operation. Validation errors calculated were comprehensively analyzed, and the differences in the implementation processes of both software tools are highlighted. The outcomes obtained help to further establish the limitations of the generic wind turbine models, thus achieving a more widespread use of Standard IEC 61400-27-1.