Thermal barrier coatings (TBCs) play a crucial role in enhancing the operating temperature of key equipment. However, when TBCs are sprayed on the internal surface of these components, there are issues related to the imperfect internal diameter atmospheric plasma spray (ID-APS) process and the unsatisfactory performance of TBCs in internal holes. Yttria-stabilized zirconia (YSZ), YSZ + Gadolinium zirconate (GZ) and YSZ + tantalate (RETaO4) TBCs were prepared using the SM F210 ID-APS gun. The thermal shock and particle erosion resistance of the coatings were compared, and the relationship between the structure and properties was investigated. The results show that the hardness, fracture toughness and erosion resistance of the three coatings are the largest in the YSZ coating and the smallest in the GZ coating. YSZ coating also has the best thermal shock resistance. These research findings have important guiding significance for the improvement of the ID-APS process.
Thermal barrier coatings (TBCs) material has excellent high-temperature resistance and heat insulation performance, which plays a vital role in improving the working efficiency and running life of the engine. During the flight, the engine will inhale dust particles in the air. These particles are mostly from siliceous debris, which are usually called calcium magnesium aluminum silicate (CMAS). At present, CMAS corrosion has become one of the important problems affecting the service life of thermal barrier coatings. In this study, conventional yttrium oxide stabilized zirconia (YSZ) coatings and ytterbium oxide and yttrium oxide co-stabilized zirconia (YbYSZ) coatings were prepared by atmospheric plasma spraying. The two coatings were examined under thermal cycling-CMAS coupling conditions and divided into six life stages. The failure modes, CMAS permeation behavior, crack characteristics and mechanical properties of the two coatings at different life stages were evaluated systematically. The experimental results show that the YbYSZ coating has a longer life than YSZ coating under the thermal cycling and CMAS coupling condition, which increases by about 83% compared with the conventional YSZ coating. In the whole life stage, the porosity of YbYSZ coating is always higher than that of YSZ coating. The phase transition is not the reason for the failure and spalling of the coatings. The crack length of the two coatings showed an increasing trend, but the crack length of the YSZ coating was higher than that of the YbYSZ coating, and the crack density of the two coatings showed a “saddle shape”, which was more obvious for the YSZ coating. The YbYSZ coating shows better mechanical properties under the thermal cycling-CMAS coupling condition with the evolution of life.
22 August 2024 in Journal of the European Ceramic Society
The development of gas turbine technology has led to an increase in the complexity of the geometric shape of the sprayed workpiece. Consequently, it has become more difficult to maintain the perpendicularity of the spraying angle during the spraying process, thereby impacting the structure and performance of the coating. This study uses the atmospheric plasma spraying method to simultaneously spray two types of powder for the preparation of embedded micro-agglomerated particle (EMAP) coatings. The spraying process is conducted at four different angles, ranging from 90° to 30°, in order to analyze the influence of the spray angle on the particle deposition and coating performance. The experimental results demonstrate that the relative deposition efficiency, hardness, and elastic modulus of the EMAP coatings decreased as the spray angle decreased. The porosity exhibited a reduction when the spraying angle dropped from 90° to 50°, followed by a significant rise at 30°. The greatest relative amount of second phase particles embedded in the coating appeared at a spraying angle of 90°, amounting to 10.8%. The smallest amount was found at a spraying angle of 30°, with a relative quantity of 2.2%. Furthermore, the molten droplets of the first phase matrix powder underwent extension and fragmentation along the angular direction at low angles. At an angle of 90°, the maximum average thermal shock life was 40.6 cycles, with the best stability of thermal shock life. The decrease in the spraying angle resulted in a deterioration in both the thermal shock life and its stability.
With the development of the aerospace industry, the close exploration of the Sun has become a human demand. However, close-range exploration means that the detection satellite needs to accept the test of high temperatures above 1400 °C, so a thermal protective coating is a necessary part of the detection satellite to isolate heat and reflected light. Al2O3 coating has the characteristics of high emissivity and low absorptivity, and it is the best choice for thermal protection coating. However, the coating is subjected to thermal cycles, including heating and cooling, as the satellite rotates around the Sun, which could result in a change in the structure and properties of the coating. Therefore, thermal shock experiments were carried out, and the influence of microstructure on the absorption rate of the Al2O3 coating was investigated. In this study, an Al2O3 coating was prepared by atmospheric plasma spraying (APS). The coating was subjected to a thermal shock (TS) test at 1400 °C using a self-made flame shock device, and coating samples under different thermal shock degrees were obtained. A scanning electron microscope (SEM) was used to characterize the coating pores, and the effects of the coating pore size, aspect ratio (A/R) and cracks in the coating on the optical properties of the coating under different thermal shock degrees were analyzed. In order to clarify the influence of coating microstructure changes on the optical properties of the coating under different thermal shock degrees, not only relevant experiments were carried out, but also the solar reflectivity of Al2O3 coatings with different pore structures was analyzed by the finite element method using finite-difference time-domain (FDTD). The results show that increasing the porosity and aspect ratio of the pores can improve the partial solar absorption of the coating. It was also found that the transverse crack propagation improves the solar reflectance of the coating.
This study uses atmospheric plasma spraying (APS) technology to prepare thermal barrier coatings (TBCs) with yttrium-stabilized zirconia (YSZ) and Yb2O3-Y2O3-co-stabilized ZrO2 (YbYSZ) materials at different spraying powers. It analyzes the differences and changes in the microstructure, thermodynamic properties, and mechanical properties of the TBCs. The CaO-MgO-Al2O3-SiO2 (CMAS) resistance of coatings was tested using thermal cycling-CMAS experiments and isothermal corrosion experiments. Compared to YSZ coatings, YbYSZ coatings have lower thermal conductivity, a higher hardness and elastic modulus, a longer lifetime under thermal cycling-CMAS conditions, and lower penetration and degradation depths. Under thermal cycling-CMAS coupling conditions, the optimal power range for the longest thermal cycling lifetime for both coatings is 39–40 kW. Overall, compared to the YSZ material, the YbYSZ material exhibits superior properties.