Modern residential roofs in Malaysia mainly employ red and brown roof tiles due to aesthetic factors and the ability of the roof surface to reflect or retard heat transfer is typically not considered the main priority. The present article reveals the findings of a study on the effect of roof tile colour on heat conduction transfer through roof tiles and ceiling boards, roof-top surface temperature and cooling load. Findings suggest that the selection of white roof tiles significantly reduces the peaks of heat conduction transfer and roof-top surface temperature as well as the values of heat conduction transfer and roof-top surface temperature throughout diurnal profiles, which consequently reduces hours of indoor thermal discomfort and use of air-conditioners in indoor spaces. A decline in peak roof-top surface temperature of up to 16.00 °C that results in annual energy savings of up to 13.14% can be achieved when the roof tile colour is changed from red to white. Further research on the development of solar-reflective paint or coating products that can significantly increase the solar reflectance values of non-white roof tiles are essential to overcome issues related to maintenance difficulties and lack of preference among house buyers towards white roof tiles.
23 March 2018 in Arabian Journal for Science and Engineering
History has shown that geopolymer cement provides high compressive strength as compared to Class G cement. However, the research had been done at ambient temperature, not at elevated condition which is the common oil well situation. In this research, the physical and mechanical properties performance of the oil well cement were investigated by laboratory work for two types of cement that are geopolymer and Class G cement. The cement samples were produced by mixing the cement according to the API standards. Class C fly ash was used in this study. The alkaline solution was prepared by mixing sodium silicate with NaOH solution. The NaOH solution was prepared by diluting NaOH pellets with distilled water to 8M. The cement samples were cured at a pressure of 3000 psi and a temperature of 130 °C to simulate the downhole condition. After curing, the physical properties of the cement samples were investigated using OYO Sonic Viewer to determine their elastic properties. Autoclave expansion test and compressive strength tests were conducted to determine the expansion value and the strength of the cement samples, respectively. The results showed that the geopolymer cement has a better physical and mechanical properties as compared with Class G cement at elevated condition.
The present study aimed to investigate the effect of an expandable additive on the compressive strength and linear expansion of geopolymer cement, which is an alternative to ordinary Portland cement, for oil-well cementing. Fly-ash-based geopolymer cement samples, with the addition of slag cement as a strength enhancer, were prepared by using an elastomeric expandable additive (R-additive), which consists of styrene–butadiene rubber with a specific gravity of 0.945, at concentrations of 10%, 15%, 20% and 25% by weight of the solid blend, and cured in a water bath at 60 °C and atmospheric pressure, and a curing chamber at 90 °C and 3000 psi, or approximately 20.68 MPa. Mixability, amount of free water and slurry density were studied, and the effects of the concentration of R-additive on the compressive strength (F) and linear expansion (∆l/l0) of the samples were analyzed. When cured at 60 °C and atmospheric pressure, the highest F of 15.01 MPa was obtained when the concentration of R-additive was 10%, while the highest ∆l/l0 of 0.9985% was obtained when the concentration of R-additive was 25%. An increase in the curing temperature and pressure to 90 °C and 3000 psi (≈20.68 MPa) resulted in the reduction of F from 15.01 to 14.62 MPa and from 10.33 to 9.61 MPa, and the increase in ∆l/l0 from 0.52% to 0.63%, and from 0.99% to 1.32%, when the concentrations of R-additive were 10% and 25%, respectively. The findings suggest that the formulations adopted, which contain R-additive at concentrations ranging from 10% to 25%, fulfilled the requirements of the oil and gas industry.
Geopolymer cement (GPC) is an aluminosilicate-based binder that is cost-effective and eco-friendly, with high compressive strength and resistance to acid attack. It can prevent degradation when exposed to carbon dioxide by virtue of the low calcium content of the aluminosilicate source. The effect of the concentration of calcium chloride (CaCl2) as the accelerator on the compressive strength and acoustic impedance of GPC for well cement, while exposed to high pressure and high temperatures, is presented. Fly ash from the Tanjung Bin power plant, which is categorized as Class F fly ash according to ASTM C618-19, was selected as the aluminosilicate source for the GPC samples. Sodium hydroxide and sodium silicate were employed to activate the geopolymerization reaction of the aluminosilicate. Five samples with a density of 15 ppg were prepared with concentrations of CaCl2 that varied from 1% to 4% by weight of cement. Findings revealed that the addition of 1% CaCl2 is the optimum concentration for the curing conditions of 100 °C and 3000 psi for 48 h, which resulted in the highest compressive strength of the product. Results also indicate that GPC samples that contain CaCl2 have a smaller range of acoustic impedance compared to that of ordinary Portland cement.