In this article, we show the feasibility of improving the performance of a high voltage and high repetition avalanche transistor pulse generator by applying a two-phase immersion cooling technique. The forced air cooling, single-phase immersion cooling, and two-phase immersion cooling techniques were applied to a 60-stage subnanosecond pulse generator. The experimental results indicate that the two-phase immersion cooling technique can effectively control the temperature rising of the avalanche transistor and, thus, reduce the time base jitter and voltage amplitude jitter. Five types of dielectric fluid with different boiling temperatures were comparatively studied. The FC-72 was finally adopted for the balanced performance on voltage amplitude and repetition rate. The two-phase immersion cooling technique could reduce the thermal resistance between the case and ambient and increase the maximum power from 330 to 876 mW. With this cooling method, the surface temperature of the transistor can be effectively controlled below 62 °C. The pulse generator could achieve outstanding performance with a voltage of 2350 V and a rise time of 180 ps. It can work stably at 200 kHz for more than 30 min, and the burst repetition rate could be 260 kHz within 1 min. This article offers new perspectives in the design of high repetitive avalanche transistorized subnanosecond generators.

Besides a typical high‐density plasma source, electrical explosion of conductors is also indispensable in switches, nanomaterial synthesis, shock‐wave sources, etc. In this paper, an experimental study regarding plasma dynamics of electrical wire explosions (μs‐timescale) is presented, with spatiotemporal resolved diagnostics. Pure Cu/Ni wire and Cu‐Ni alloy wire were used and compared. The alloy wire usually has a higher resistivity, resulting in a higher initial energy deposition (heating) rate. Abel inverse transformation indicated that the plasma radiation focussed on the outer region of the discharge channel for the alloy wire. In addition, the metallic vapour determined by the material properties had a considerable influence on the plasma process and resulting nanomaterials. In particular, both transverse and axial‐layered structures were observed in alloy wire vapour. In addition, for the first time, the expanding arc‐like plasma of explosion products was understood and examined from aspects of material properties and energy relaxation. The later stage of wire explosion resembled the state of regular metal vapour arcs under 1 MPa pressure. Finally, the core factor for the fast energy deposition stage of wire explosion was ascertained. Correlations between pre‐exposition circuit parameters and post‐explosion dynamic effects were found, which is significant for practical applications.

Avalanche transistor Marx bank circuits (MBCs) are widely used in high voltage repetitive nanosecond pulse generators, but problems exist with respect to increasing the output voltage due to the limited pulsed current. Accordingly, a novel topology based on an avalanche transistor MBC combined with a linear transformer driver is proposed, the latter of which exhibits advantageous stress distribution and modular structure. A four-module prototype with four units in each module is developed in the laboratory. The output characteristics are investigated by varying important parameters such as the main capacitance, the number of conducting units, the number of cascaded modules, and the trigger signal time delay. The test results verify the validity of the proposed topology. For a 50 $\mathrm{\Omega }$ resistive load, the prototype can generate pulses with an amplitude of 10.9 kV, a rise time of 3.3 ns, and a voltage superposition efficiency of 89%. The topology proposed in this paper may help to provide a method to further improve the output performance of avalanche transistor MBCs.

In this paper, a 60-stage Marx circuit with the two-phase immersion cooling technique is presented. The performance parameters of the pulse generator with phase change immersion cooling and forced air cooling are compared. The results show that the maximum repetition rate is increased from 80 to 260 kHz, the pulse drift is significantly reduced from 900 to 200 ps, and the temperature rise of transistors is controlled effectively to enhance the stability of the amplitude. We also studied the influence of temperature on the turn-on and turn-off processes of the transistors to show the importance of heat management under high repetition conditions. Finally, a pulse generator is developed with the repetition rate of 200 kHz, the rise time of 180 ps, and the amplitude of 2350 V on a matched 50 $\mathrm{\Omega }$ resistive load, which can work for more than 30 min.

Low-temperature plasma technology is widely used in various industrial fields, which require the plasma to be of large volume, diffuse, and stable. Furthermore, previous studies have shown that better plasma performance has been obtained by using generators with a high voltage, a high repetition rate, a fast rise time, and a short pulse duration. In this paper, a novel topology is proposed for such generators, which is based on magnetic switches and diode opening switches. A prototype is developed, and its output characteristics are investigated by varying essential parameters, such as the load resistance and the power supply voltage. The experimental results show that it can generate pulses with a voltage of 30.6 kV, a rise time of 7.1 ns, a pulse duration of 8.2 ns, and a maximum repetition rate of 12 kHz on a 300 Ω resistive load. The prototype has been successfully used to drive uniform plasma in ambient air. In the proposed topology, a diode is added to make the magnetic cores independent of each other, significantly simplifying the design calculation. It may help develop nanosecond solid-state generators.

Solid‐state high voltage high repetitive pulse generators have a broad prospect in various applications. The high power and high‐frequency operation of the pulse generator suffer from the massive heat dissipation problem, which limits the improvement of the output parameters and even affects the lifetime. This article focuses on heat management technology for high voltage high repetitive pulse generators. Firstly, the typical circuit topology of the high repetitive pulse generators was summarised. From the perspective of different application requirements, the demands of the heat management design were concluded. Moreover, the heat generation characteristics and difficulties of solid‐state high voltage high repetitive pulse generators were analysed. Then, the different state‐of‐art cooling techniques were reviewed, and their applicability and limitations for the high voltage high repetitive generators were discussed. Finally, a flow chart for heat management design was given.