12 June 2019 in IEEE Transactions on Power Electronics
Marx bank circuits (MBCs) based on avalanche transistors are widely used to generate nanosecond pulses with high power, high repetition rate and low jitter. However, it was observed that avalanche transistors in the first and second stages of traditional M×N-stage MBCs have high failure rates. This paper proposes an auxiliary triggering topology (ATT) for improving the reliability of high power MBCs based on avalanche transistors. Operation principles of ATT and failure mechanisms of MBCs are analyzed. By adopting ATT, auxiliary triggering pulse is generated between the base and emitter of the transistor, and the switching mode is changed from “overvoltage switching-on” to “triggering switching-on”. The combined effect of overvoltage ramp and auxiliary triggering pulse significantly reduces the failure rates of easily damaged transistors. Two nanosecond pulse generators, 3×12-stage and 6×10-stage MBCs adopting ATT, are developed to verify the feasibility of the proposed configuration. The output amplitude and the rising time are 8.5 kV/6 ns and 17 kV/6 ns at the open end of coaxial cable with 75 Ω impedance, respectively. Both generators are tested continuously at 2 kHz for 60 minutes and no failure occurs, which show much better performance in repetition rate and reliability than traditional M×N-stage MBCs.
8 May 2020 in IEEE Transactions on Instrumentation and Measurement
Avalanche transistor-based Marx bank circuit (MBC) is widely used to generate nanosecond pulses with high amplitude, high repetition rate, fast rise time and low jitter. Recently, the problem that avalanche transistors in the first several stages of M×N-stage MBC fail frequently has been alleviated by adopting auxiliary triggering topology (ATT). However, the reasons for improvement and the optimal design method have not been fully understood. In this paper, a flexible 4×10-stage MBC is developed to further investigate the output characteristics under different modified stages, capacitors and loads through both experiments and simulations. The results show that on the one hand, adopting ATT will cause energy loss of main capacitors to auxiliary triggering capacitors, which can decrease the output voltage; on the other hand, transistors operating in auxiliary triggering switching-on mode have lower residual voltage than in overvoltage switching-on mode, which can increase the output voltage. This implies that there exists an optimal value of modified stages, which is 5 for the 4×10-stage MBC. Besides, by adopting ATT, the waveform of output pulse changes, and the rising edge becomes faster. Finally, a repetitive nanosecond pulse generator is developed based on the optimized parameters, which can produce pulses with amplitude of 9.04 kV, rise time of 3.4 ns, pulse width of 18.8 ns and maximum repetition rate of 1 kHz at the 75Ω openended cable. And the feasibility of this modified MBC is validated by the preliminary experiments of driving atmospheric pressure plasma jet (APPJ).
9 June 2021 in IEEE Transactions on Power Electronics
The avalanche transistor-based Marx circuit has great advantages in generating high-voltage nanosecond pulses. The introduction of auxiliary triggering topology (ATT) can reduce the damage probability of transistors in M × N-stage Marx bank circuits (MBCs). However, as the number of modified stages increases, the output voltage drops significantly, which makes it not achievable to adopt ATT at each stage. The transistors in nonmodified stages still have a certain failure rate when operating at a high repetition rate. Moreover, the previous ATT is only applicable in the negative polarity MBC. In this article, an improved ATT is proposed to solve the above problems. First, its operating principle is analyzed, and the feasibility of its application in both negative and positive MBCs is verified by simulations. Then, the effects of the improved ATT on M × N-stage MBCs are experimentally studied, and the results show that the improved ATT can be used in all stages of MBC without reducing the output voltage. It can also reduce the minimum operating voltage of transistors and widen the regulating range of output voltage. In addition, it can improve the synchronous conduction of parallel-connected transistors. Finally, two nanosecond pulse generators with positive and negative polarity, respectively, are developed and used to drive the atmospheric pressure plasma jet. The amplitude of output voltage can be adjusted in the range of 5-10 kV, measuring at the open end of a coaxial cable with 75 Ω impedance, and the maximum repetition rate is up to 7 kHz.
18 April 2022 in IEEE Transactions on Instrumentation and Measurement
In order to further improve the output voltage amplitude and repetitive operation reliability of nanosecond pulse generator (PG) based on avalanche transistor (AT), the method of power synthesis of modularized Marx circuits with transmission line transformer (TLT) is employed in this article. The modified positive $4\times11$ -stage Marx circuit introducing base-triggering method is designed and implemented to improve the operation reliability. The triggering synchronization and the consistence of output characteristics of multiple Marx modules with an identical trigger pulse are validated. The feasibility of combining pulses generated from four Marx modules with an optimized four-stage TLT is demonstrated. The influences of the type and quantity of magnetic core and the superimposed stage number of TLT on the output performance of the generator are investigated. The operation characteristics of the generator including output parameters, trigger time-delay, and loop efficiency in the whole working range are evaluated. The experimental results show that the working range of the overall device has been widened significantly with the injection of additional initial carrier. Accordingly, the generator prototype is capable of achieving the output performance with an adjustable voltage amplitude in the range of 7.8–26.7 kV on a matched 300- $\Omega $ resistive load and 12.2–38.9 kV on the high-resistance load, respectively, a 10%–90% rise time of 3.6 ns, and a full-width at half-maximum (FWHM) of 12.2 ns. A long-term test with the maximum repetition rate of 3 kHz is conducted to realize high-voltage output and high-frequency operation simultaneously.
1 March 2021 in Review of Scientific Instruments
Avalanche transistor Marx bank circuits (MBCs) are widely used in high voltage repetitive nanosecond pulse generators, but problems exist with respect to increasing the output voltage due to the limited pulsed current. Accordingly, a novel topology based on an avalanche transistor MBC combined with a linear transformer driver is proposed, the latter of which exhibits advantageous stress distribution and modular structure. A four-module prototype with four units in each module is developed in the laboratory. The output characteristics are investigated by varying important parameters such as the main capacitance, the number of conducting units, the number of cascaded modules, and the trigger signal time delay. The test results verify the validity of the proposed topology. For a 50 resistive load, the prototype can generate pulses with an amplitude of 10.9 kV, a rise time of 3.3 ns, and a voltage superposition efficiency of 89%. The topology proposed in this paper may help to provide a method to further improve the output performance of avalanche transistor MBCs.
26 April 2021 in IEEE Transactions on Instrumentation and Measurement
Avalanche transistor (AT)-based repetitive nanosecond pulse generators with high amplitude, fast rise time, narrow pulse width, and low jitter have been widely developed and applied in numerous fields. However, relatively little research has been carried out on the positive nanosecond pulse generation with high flexibility in a wide range of output voltage amplitude. In this article, a novel AT-based Marx circuit (MC) topology adopting base-triggering method is proposed to avoid the formation of current filamentation inside the transistors and resolve the contradiction between high-voltage output and high repetition rate operation. A 6×10-stage MC prototype is implemented with optimized parameters to validate the feasibility of the proposed topology. The conduction processes of transistors show that, with the injection of additional base current, the switched-ON modes are transformed, which contributes to reliable conduction of transistors even without sufficient overvoltage ramp. With the adoption of inner triggering loops, the minimum working voltage of the prototype is extended to 1150 V. The operation characteristics of the generator in the whole operation range are investigated in depth. Experimental results illustrate that, at the 75- Ω match-ended coaxial cable, the prototype is capable of generating positive pulses with an adjustable voltage amplitude in the range of 6.50 to 12.39 kV, a basically consistent rise time of 3.6 ns and pulse width of 19.5 ns. Over 10 7 successive pulses are generated at a maximum repetition rate of 1 kHz without any device failure.