The present study investigates the feasibility of utilizing polylactic acid (PLA) and PLA-based natural fiber-reinforced composites (NFRCs) in mechanical recycling. A conical twin screw extrusion (CTSE) process was utilized to recycle PLA and PLA-based NFRCs consisting of 90 wt.% PLA and a 10 wt.% proportion of either basalt fibers (BFs) or halloysite nanotubes (HNTs) for up to six recycling steps. The recycled material was then injection molded to produce standard test specimens for impact strength and tensile property analysis. The mechanical recycling of virgin PLA led to significant discoloration of the polymer, indicating degradation during the thermal processing of the polymer due to the formation of chromatophores in the structure. Differential scanning calorimetry (DSC) analysis revealed an increase in glass transition temperature (T_g) with respect to increased recycling steps, indicating an increased content of crystallinity in the PLA. Impact strength testing showed no significant detrimental effects on the NFRCs’ impact strength up to six recycling steps. Tensile testing of PLA/HNT NFRCs likewise did not show major decreases in values when tested. However, PLA/BF NFRCs exhibited a significant decrease in tensile properties after three recycling steps, likely due to a reduction in fiber length beyond the critical fiber length. Scanning electron microscopy (SEM) of the fracture surface of impact specimens revealed a decrease in fiber length with respect to increased recycling steps, as well as poor interfacial adhesion between BF and PLA. This study presents a promising initial view into the mechanical recyclability of PLA-based composites.

The Global Program to Eliminate Lymphatic Filariasis (GPELF) is a program that aims to eliminate lymphatic filariasis by 2030. The GPELF strategy is based on interrupting transmission using mass drug administration (MDA) and, in parallel, managing morbidity cases. However, it has been seen that there is a shortage of research in the literature and public policies regarding this last pillar. In this study, we reviewed the literature and available information regarding the burden of filarial morbidity. In addition, we identified that in the Americas, the implementation of structured services with regard to morbidity assistance in the Americas was scarce. We formed a review that aimed to assess the pathogenesis, epidemiology, repercussions, and treatment of filarial morbidity in countries in the Americas where lymphatic filariasis is endemic. Structured searches were carried out on PubMed, LILACS, Scopus, and Web of Science databases without time and language restrictions. Three reviewers evaluated the 2150 studies and performed data extraction, and quality assessment by assigning scores to the studies found. The current literature and available information on the burden of filarial morbidity, as well as the implementation of structured services with regard to morbidity assistance in the Americas, were all found to be scarce. Now that this knowledge gap has been identified, both health services and researchers need to seek the implementation and enhancement of the maintenance of GPELF strategies that relate to the morbidity pillar.

Four-dimensional printing is primarily based on the concept of 3D printing technology. However, it requires additional stimulus and stimulus-responsive materials. Poly-N-vinylcaprolactam is a temperature-sensitive polymer. Unique characteristics of poly-N-vinylcaprolactam -based hydrogels offer the possibility of employing them in 4D printing. The main aim of this study is to alter the phase transition temperature of poly-N-vinylcaprolactam hydrogels. This research focuses primarily on incorporating two additional monomers with poly-N-vinylcaprolactam: Vinylacetate and N-vinylpyrrolidone. This work contributes to this growing area of research by altering (increasing and decreasing) the lower critical solution temperature of N-vinylcaprolactam through photopolymerisation. Poly-N-vinylcaprolactam exhibits a lower critical solution temperature close to the physiological temperature range of 34–37 °C. The copolymers were analysed using various characterisation techniques, such as FTIR, DSC, and UV-spectrometry. The main findings show that the inclusion of N-vinylpyrrolidone into poly-N-vinylcaprolactam increased the lower critical solution temperature above the physiological temperature. By incorporating vinylacetate, the lower critical solution temperature dropped to 21 °C, allowing for potential self-assembly of 4D-printed objects at room temperature. In this case, altering the lower critical solution temperature of the material can potentially permit the transformation of the 4D-printed object at a particular temperature.

This study addresses the gap in research on the application of thermochromic polymers (TPs) in food packaging and their potential for real-time temperature monitoring, aiding in the assessment of food quality and shelf-life. TPs exhibit a visible color change in response to temperature variations. A comprehensive systematic review (SR) across multiple engineering peer-review databases using predefined terms was conducted. Additionally, international patent databases were investigated using the same predefined terms. Independent experts reviewed the methodology to identify and address potential biases. A total of 288 eligible articles and 922 patents were identified. After a duplicate selection and extraction process according to the inclusion criteria, four related full-text publications were selected from the initial 288 articles, and five relevant patents were selected from the 922 patents. The qualitative review suggests that TPs hold significant promise as food packaging materials due to their unique physical properties. The study concludes that TPs offer valuable properties for the food packaging industry, meriting further investigation to exploit their benefits fully.

Injection moulding is a polymer processing method of choice for making plastic parts on industrial scale, but its traditional mould is made from tooling steel with time-consuming and costly production. Additive manufacturing technologies arise as an alternative for creating mould inserts at lower costs and shorter lead times. In this context, this study describes a series of stereolithography (SLA)-printed injection mould inserts fabricated from two photopolymer resins, utilised to mould standard tensile specimens of a commercial-grade polypropylene, aiming to evaluate effects on the polymer’s thermal and mechanical properties. Our results demonstrated that the glass fibre-filled resin inserts withstood more moulding cycles before failure, had superior mechanical properties, higher T_g and greater thermal conductivity. Calorimetric data revealed that PP thermal properties and degree of crystallinity were little affected, while mechanical testing suggests a significant effect in the elongation at break. Thus, these findings highlight the importance of adequate heat extraction during injection moulding and endorse further application of SLA mould inserts for the manufacturing of injection-moulded plastic parts in the case of prototypes or small batches, provided suitable cooling is made available, contributing to the feasibility and affordability of employing this approach for an industrial setting.