Metal-organic frameworks (MOFs) are highly crystalline inorganic-organic complexes formed from metal ions or metal clusters and multi-toothed organic ligands. MOFs have great potential for use in antibacterial materials in the biological, environmental, and food antimicrobial fields. They can act as a reservoir of metal ions, releasing them gradually and leading to a sustained antibacterial effect analogous to that proposed for metal oxide nanoparticles (NPs). Herein, UiO-66-NH2 as a type of MOF was first prepared by a facile solvothermal method and then loaded with Ag NPs to form a Ag/UiO-66-NH2 composite and the different materials were synthesized by controlling silver doping amount, which are then applied to an antibacterial test. Works on the synthesis of Ag/UiO-66-NH2 and its antibacterial test were not reported before. The synthesized materials were characterized using the field emission scanning electron microscope (FE-SEM), X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FT-IR), Brunauer-Emmett-Teller (BET), thermal gravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS) techniques. The antibacterial activity of the Ag/UiO-66-NH2 was then assessed against E. coli (gram-negative bacteria) and Staphylococcus aureus (gram-positive bacteria), using the inhibition zone (ZIO) method and optical density (OD) method. The obtained results have shown that the introduction of Ag does not interfere with the crystallization of UiO-66-NH2. The FT-IR spectral profiles recorded for the UiO-66-NH2 samples fabricated under conditions of varying silver ion doping levels are similar to those recorded for UiO-66-NH2. The thermal stability of UiO-66-NH2 containing varying amounts of silver ions was lower than the thermal stability of UiO-66-NH2. However, under these conditions, the specific surface area and pore volume increased. The antibacterial performance of UiO-66-NH2 improved significantly following the process of silver ion doping. The best antibacterial performance was observed when the silver ion content was 4 wt.%. Overall, we synthesized a new nanocomposite material with broad-spectrum bacterial sterilization, which was easy to manufacture.
With the exploring and developing of mineral resources in the Tibet Autonomous Region for many years, a large number of tailings have been produced. A total of 17 tailings samples from borehole cores were collected from different tailings ponds in different regions of Tibet. The results showed that the mineral composition and content of tailings in each research area were different. Among them, quartz was the most abundant mineral in most tailings. The major elements of tailings mainly included Si, Al, Fe, Mg, Mn, Ca, Na, K and so on. S existed in different types of tailings. In the analysis of trace element composition, it was found that the content of some elements had approached the lowest industrial grade, which has potential recycling value, such as Mn, Zn, Pb and P. Through the detection of radioactive elements (Ra-226, Th-232 and K-40), it was shown that there were great differences among different types of tailings, and their different contents would bring potential hazards to the safety of the surrounding environment and human health. Similar results were found in the analysis of particle size characteristics of tailings. These results are of great significance for the future utilization and resource utilization of tailings pond.
It is of great significance to search for efficient, renewable, biodegradable and economical membrane materials. Herein, we developed an organic-inorganic hybrid regenerated cellulose membrane (ZrO2/BCM) with excellent hydrophilic and anti-fouling properties. The membrane was prepared by introducing ZrO2 particles into an N-Methylmorpholine-N-oxide(NMMO)/bamboo cellulose(BC) solution system by the phase inversion method. The physi-chemical structure of the membranes were characterized based on thermal gravimetric analysis (TGA), Fourier transform infrared spectroscopy (ATR-FTIR), field emission scanning electron microscopy (FE-SEM), and X-ray diffraction (XRD). The modified regenerated cellulose membrane has the excellent rejection of bovine serum albumin (BSA) and anti-fouling performance. The membrane flux of ZrO2/BCM is 321.49 (L/m2·h), and the rejection rate of BSA is 91.2%. Moreover, the membrane flux recovery rate after cleaning with deionized water was 90.6%. This new type of separation membrane prepared with green materials holds broad application potential in water purification and wastewater treatment.
Water scarcity and water pollution have become increasingly severe, and therefore, the purification of water resources has recently garnered increasing attention. Given its position as a major water resource, the efficient purification of drinking water is of crucial importance. In this study, we adopted a phase transition method to prepare ZrO2/BCM (bamboo cellulose membranes), after which we developed IP-ZrO2/BC-NFM (bamboo cellulose nanofiltration membranes) through interfacial polymerization using piperazine (PIP) and tricarbonyl chloride (TMC). Subsequently, we integrated these two membranes to create a combined “ultrafiltration + nanofiltration” membrane process for the treatment of drinking water. The membrane combination process was conducted at 25 °C, with ultrafiltration at 0.1 MPa and nanofiltration at 0.5 MPa. This membrane combination, featuring “ultrafiltration + nanofiltration,” had a significant impact on reducing turbidity, consistently maintaining the post-filtration turbidity of drinking water at or below 0.1 NTU. Furthermore, the removal rates for CODMN and ammonia nitrogen reached 75% and 88.6%, respectively, aligning with the standards for high-quality drinking water. In a continuous 3 h experiment, the nanofiltration unit exhibited consistent retention rates for Na2SO4 and bovine serum protein (BSA), with variations of less than 5%, indicating exceptional separation performance. After 9 h of operation, the water flux of the nanofiltration unit began to stabilize, with a decrease rate of approximately 25%, demonstrating that the “ultrafiltration + nanofiltration” membrane combination can maintain consistent performance during extended use. In conclusion, the “ultrafiltration + nanofiltration” membrane combination exhibited remarkable performance in the treatment of drinking water, offering a viable solution to address issues related to water scarcity and water pollution.
In this study, by adding zirconium anhydride (ZrO2) particles to a solution of N–methylmorphorphine–N–oxide (NMMO) and bamboo cellulose (BC), we used interfacial polymerization (IP) to obtain regenerated cellulose nanofiltration membranes (IP–ZrO2/BC–NFMs) that exhibited high water flow and rejection of salts and dyes. During interfacial polymerization, anhydrous piperazine (PIP) was used as the waterborne monomer, and 1,3,5–trimesoyl chloride (TMC) and n–hexane were used as the organic phase. The procedure was adjusted by analyzing the impacts of the concentrations of the water and organic phase monomers and the reaction duration on the performance of the developed IP–ZrO2/BC–NFMs. The chemical structures and morphologies of the as–obtained IP–ZrO2/BC–NFMs were examined using various characterization techniques. The performance of these membranes for removal of inorganic salts and dyes as well as their water flow were investigated. IP–ZrO2/BC–NFMs obtained at a pressure of 0.5 MPa, PIP concentration of 1.5 wt.%, TMC concentration of 0.15 wt.%, and polymerization period of 2 min displayed the highest water flux (55.12 LMH) and the best desalination effect (NaCl rejection rate = 19.15%). Over 90% of both Methyl Blue (MB) and Congo Red (CR) dyes were intercepted. We demonstrated that the addition of ZrO2 to nanofiltration membranes significantly enhanced the water flow of the IP–ZrO2/BC–NFMs as well as the salt ion rejection rate.
2-Methyltetrahydrofuran (2-MTHF), a hydrogenated derivative of levulinic acid (LA), is a biomass-derived platform compound with diverse and significant applications as a biofuel, gasoline additive, green solvent, and pharmaceutical synthesis intermediate. This study investigates the preparation of a Cu1Ni2/Al2O3 catalyst through the calcination–reduction of CuNiAl hydrotalcite as a precursor, which was subsequently utilized in the hydrogenation of LA to produce 2-MTHF. The calcination–reduction process applied to CuNiAl hydrotalcite results in a lattice confinement effect. This method not only disperses the active metal sites but also alters the bonding patterns of the active metals, thereby enhancing the activity and stability of the Cu1Ni2/Al2O3 catalyst. The results indicate that complete conversion of LA and a 2-MTHF yield of 87.6% can be achieved under optimal conditions of 190 °C, 5 MPa hydrogen, and a reaction time of 5 h, demonstrating an efficient one-step conversion process. Additionally, the catalyst’s recyclability was assessed through multiple reuse tests, with a loss of activity of only 9.2% after six cycle experiments, suggesting its feasibility and reliability for industrial applications.